SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Carving a Wooden Clog — The All-Wood Sabot from a Single Green Block
Woody

Dibuat oleh

Woody

2. Juli 2026NO
33
0
0
0
0

Carving a Wooden Clog — The All-Wood Sabot from a Single Green Block

Across rural Europe the wooden clog — the French sabot, the Dutch klomp — kept feet warm and dry for centuries. Each shoe is carved from a single block of green hardwood: the outside shaped like a foot, the inside hollowed out to receive it. Green (unseasoned) alder, willow or beech is used because it carves easily and splits little, then hardens as it dries. This blueprint carves one clog from froe-split billet to finished shoe, then repeats for the matching pair, using only edge tools.
Menengah
6

Instruksi

1

Split a clean billet

Split a straight-grained block of green alder, willow or beech to a little larger than the foot, using the froe driven with a wooden mallet. Choose a length free of knots so the wood carves cleanly.

Material untuk langkah ini:

Hardwood BlockHardwood Block1 buah

Alat yang dibutuhkan:

FroeFroe
Wooden MalletWooden Mallet
2

Rough out the foot profile

With the hatchet, chop the billet down to the rough shape of a foot seen from the side — a flat sole, an upturned toe, and a squared heel. Leave the block oversize everywhere for now.

Alat yang dibutuhkan:

HatchetHatchet
3

Mark the sole and top outlines

Stand the block on the wearer's foot or a pattern and mark the outline of the sole and the top opening with the point of the carving knife, so you have clear lines to carve to.

Alat yang dibutuhkan:

Sloyd Carving KnifeSloyd Carving Knife
4

Shape the outside with the drawknife

Clamp the block and draw the drawknife toward you to shape the rounded outside of the clog — the swell of the toe, the waist at the instep, and the flat of the sole. Work down to the marked lines.

Alat yang dibutuhkan:

Draw KnifeDraw Knife
5

Refine the curves with a spokeshave

Smooth the toe curve, the sides and the instep with the spokeshave, fairing the outside into an even foot shape ready to hollow.

Alat yang dibutuhkan:

SpokeshaveSpokeshave
6

Bore out the mouth

Bore down into the top opening with the hand auger to remove the bulk of the inside waste quickly, stopping short of the sole so you do not bore through.

Alat yang dibutuhkan:

Hand AugerHand Auger
7

Hollow the foot cavity

Hollow the inside to the shape of a foot with the hook knife and gouge, driven by the mallet where needed. Follow the curve of the sole and open out under the instep, leaving even walls.

Alat yang dibutuhkan:

Hook Knife (Spoon Carving)Hook Knife (Spoon Carving)
GougeGouge
Wooden MalletWooden Mallet
8

Fit the cavity to the foot

Test the hollow against the foot it must fit: the sole should sit flat, the toes have room, and the walls be thin enough to be light but thick enough to be strong. Pare away any tight spots.

Alat yang dibutuhkan:

Hook Knife (Spoon Carving)Hook Knife (Spoon Carving)
9

Cut the instep throat

Shape the opening at the top of the foot — the 'throat' — with the gouge and carving knife so the foot slides in and the clog grips the instep without pinching.

Alat yang dibutuhkan:

GougeGouge
Sloyd Carving KnifeSloyd Carving Knife
10

Smooth inside and out

Pare every surface smooth, inside and out, with the carving knife and spokeshave, removing tool ridges so nothing chafes the foot and the outside is clean.

Alat yang dibutuhkan:

Sloyd Carving KnifeSloyd Carving Knife
SpokeshaveSpokeshave
11

Carve the matching clog

Repeat every step to carve the second clog as a mirror image of the first, so the pair matches in length, depth and shape — one left, one right.

Material untuk langkah ini:

Hardwood BlockHardwood Block1 buah

Alat yang dibutuhkan:

HatchetHatchet
Draw KnifeDraw Knife
Hook Knife (Spoon Carving)Hook Knife (Spoon Carving)
12

Dry the pair slowly

Set the finished green-wood clogs to dry slowly in a cool, airy place away from direct heat. As the wood seasons it hardens and the clogs become light and durable — drying too fast would crack them.

Bahan

1

Alat yang Diperlukan

9

Bahan cetak biru terhubung

Carving a Wooden Bowl with an Adze — Hollowing from a Green Wood Blank
10% Atribusi

Carving a Wooden Bowl with an Adze — Hollowing from a Green Wood Blank

oleh WoodyNO

Pengerjaan Kayu

37
0
0
0
2
0

Blueprint terkait

Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip

Using a Drawknife — Shaping Riven Timber by Drawing a Blade Toward You

Using a Drawknife — Shaping Riven Timber by Drawing a Blade Toward You

oleh WoodyNO

Pengerjaan Kayu

23
0
0
0
1
0
Building a Shave Horse — The Foot-Operated Clamping Bench for Green Woodworking

Building a Shave Horse — The Foot-Operated Clamping Bench for Green Woodworking

oleh WoodyNO

Pengerjaan Kayu

37
0
0
0
1
0
Building a Pole Lathe for Green Wood Turning — Spring-Pole Reciprocating Lathe

Building a Pole Lathe for Green Wood Turning — Spring-Pole Reciprocating Lathe

oleh WoodyNO

Pengerjaan Kayu

154
1
0
0
2
0

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...