Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Chinese Dragon Kite: Bamboo-Ring Head With Revolving Eyes and 20 Sections on a Seine-Twine Harness (Boy Mechanic, 1919)
Spartan

Dibuat oleh

Spartan

13. November 2026NO
7
0
0
0
0

Chinese Dragon Kite: Bamboo-Ring Head With Revolving Eyes and 20 Sections on a Seine-Twine Harness (Boy Mechanic, 1919)

C. M. Miller's dragon kite from The Boy Mechanic, Book 3 (1919): a 12 in bamboo-ring head with horns and two paper eyes that spin in the wind, followed by up to 20 round section kites, each with a 36 in balancer stick, tied 30 in apart on three cords of seine twine. Twenty sections make a kite about 50 ft long.
Lanjutan
Several days

Instruksi

1

Strip lengths and kite length

Memuat notebook Jupyter…
2

Read The Boy Mechanic, Book 3

"Dragon kites are made as hideous as the maker can possibly conceive, and while the one to be considered is no beauty, it is more droll than fierce-looking."
3

Split and pare the bamboo

Split bamboo into strips about 3/16 in wide and pare them to less than 1/16 in thick for the head's inner ring A. To bend a strip to a sharp angle, heat it over a candle flame until it gives under pressure, bend it, and it keeps its shape when cold.

Material untuk langkah ini:

Bilah bambu panjangBilah bambu panjang1 buah

Alat yang dibutuhkan:

Pisau lipat bajaPisau lipat baja
LilinLilin
4

Frame the head

Make ring A 12 in across from a strip about 38 in long, lapping the ends and winding them with linen thread (or with wet pasted strips of rice paper about 1/2 in wide, which bind as they dry). Lash two crosspieces B and C of the same stock 3-1/2 in apart, parallel and equally spaced from the centre, their ends bent sharply and lashed inside the ring. Lash two eye rings D and E, 3-1/2 in across, between them, shaped round a 3-1/2 in cylinder so they are true. Lash stiffeners F and G, 1/16 by 1/8 by 20 in, across the back. Add outer ring H, 3 in outside A (18 in across), of 1/8 in strip under 1/16 in thick, in two pieces if needed, and the short pieces J and K between the rings. Lash the horn supports, 1/8 in wide, to the upper crosspiece and both rings, with L and M halfway between the ends of F and G and radiating from the centre of A, and N and O pointing at the eye-ring centres (Fig. 2).

Material untuk langkah ini:

Bilah bambu panjangBilah bambu panjang1 buah
Benang linenBenang linen1 buah

Alat yang dibutuhkan:

Pisau lipat bajaPisau lipat baja
LilinLilin
Meteran GulungMeteran Gulung
GuntingGunting
5

Cover and paint the head

Cover only the inside of ring A, the horns and the ears with Chinese rice paper, stretched tight with no bagging, leaving the eye rings open. Put the rings on the horns and stick ends, 1/2 to 2 in across, cut from stiff paper (larger ones of bamboo). Shade with a brush and water colours, leaving the face white or tinting it; leave the horns white and colour the tongue red (Fig. 1).

Material untuk langkah ini:

Kertas nasi (kertas beras)Kertas nasi (kertas beras)1 buah
Lem kanji teriguLem kanji terigu1 buah
Kertas KartonKertas Karton1 buah
Cat airCat air1 buah

Alat yang dibutuhkan:

Kuas lemKuas lem
Set kuas senimanSet kuas seniman
GuntingGunting
6

Make the revolving eyes

Pare bamboo to 1/32 in and form each eye into a true ring 3-1/4 in across. Pass a wire axle exactly on a diameter through the eye ring and through its socket ring D or E, with a glass bead on the wire each side between the two rings; fix the wire to the eye ring with a strip of paper wrapped tight and pasted. Cover each side halfway with rice paper, the front upper half and the back lower half, so the wind turns the eye. Blacken the front upper half and paste a round pupil between the halves so it shows on both sides (Figs. 3, 4).

Material untuk langkah ini:

Bilah bambu panjangBilah bambu panjang1 buah
Kawat besiKawat besi1 buah
Manik kacaManik kaca4 buah
Kertas nasi (kertas beras)Kertas nasi (kertas beras)1 buah
Lem kanji teriguLem kanji terigu1 buah
Cat airCat air1 buah

Alat yang dibutuhkan:

Pisau lipat bajaPisau lipat baja
Tang Berujung RataTang Berujung Rata
GuntingGunting
Set kuas senimanSet kuas seniman
7

Make the section kites

For each section make a 12 in ring of bamboo 1/8 in wide and 1/16 in thick and cover it tight like the head. Lash on a balancer stick 36 in long, small, light and well balanced, at about the place of cross-stick F, with tufts of tissue paper or feathers at its tips. Colour the discs as you like; give the last section's balancer streamers of light cloth (Figs. 5, 6). Sections may instead be 9 in with 30 in balancers, but uniform sections are better and easier.

Material untuk langkah ini:

Bilah bambu panjangBilah bambu panjang1 buah
Benang linenBenang linen1 buah
Kertas nasi (kertas beras)Kertas nasi (kertas beras)1 buah
Lem kanji teriguLem kanji terigu1 buah
Kertas tisu warnaKertas tisu warna1 buah
BuluBulu1 buah
Kain KatunKain Katun1 buah
Cat airCat air1 buah

Alat yang dibutuhkan:

Pisau lipat bajaPisau lipat baja
LilinLilin
GuntingGunting
Set kuas senimanSet kuas seniman
8

Tie the harness and bridle

Cut three cords of six-ply hard-twisted seine twine as long as the kite plus the knots. Fasten the head to a wall, tie the three cords to it at T, U and V (Fig. 2), and tie each section at the matching points exactly 30 in from the last (Fig. 7). Tie a three-string bridle to the head at T, U and V, the lower string longer than the two upper ones so the head, and with it every section, leans to the wind. A ball balancer of bamboo strips may hang from the head (Fig. 8).

Material untuk langkah ini:

Benang jaringBenang jaring1 buah
Benang layang-layangBenang layang-layang1 buah
Bilah bambu panjangBilah bambu panjang1 buah

Alat yang dibutuhkan:

Meteran GulungMeteran Gulung
GuntingGunting
9

Flying and troubleshooting

Dragon kite flying.

Flow

Loading...
10

History and honest limits

From "How to Make Combined Kites, Part I: A Dragon Kite" by C. M. Miller, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 145-148). He gives no bridle lengths and no line size beyond "a strong cord". Fig. 2 also marks 5 in at the horn tip and 1 in where F passes ring H. The tools and metric figures are ours.

Bahan

13

Alat yang Diperlukan

7

Cetak biru ini membuat

Blueprint terkait

Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...