Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Nylon Insert Lock Nut: a Nylon Collar Crimped into a Steel Nut
English
Forge

Dibuat oleh

Forge

18. Oktober 2026NO
27
0
0
0
0

Nylon Insert Lock Nut: a Nylon Collar Crimped into a Steel Nut

A nut that will not shake loose. A nylon collar sits in a recess at the top of the nut; its hole is a little smaller than the bolt, so the bolt presses its own thread into the nylon and the nylon grips it. Sauer (US 2,450,694, 1948) chose nylon over the older fibre collar: it hardly takes up water and still locks after 50 to 100 re-uses. The collar is held as Swanstrom's patent (US 2,153,681, 1939) shows: the recess wall is pressed in and crimped over it. Size M10 is ours. The picture: a nylon-insert lock nut (Wikimedia Commons).
Menengah
Half a day

Instruksi

1

Cut and turn the blank

Saw a blank from hex bar. On the lathe, turn the top part round, with a wall that tapers toward the top.

Material untuk langkah ini:

Batang segi enam baja lunakBatang segi enam baja lunak1.5 cm

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Mesin Bubut LogamMesin Bubut Logam
Pahat bubutPahat bubut
Jangka Sorong VernierJangka Sorong Vernier
2

Drill and tap

Drill through and tap an M10 thread.

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
Set pembuat ulirSet pembuat ulir
Jangka Sorong VernierJangka Sorong Vernier
3

Counterbore the top

Counterbore the top of the bore with an ordinary twist drill. It leaves a recess with a conical floor.

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
Jangka Sorong VernierJangka Sorong Vernier
4

Mould the nylon collar

Mould a nylon washer that fits the recess, with a hole somewhat smaller than the bolt's outside thread diameter. Nylon is thermoplastic, so scrap can be moulded again.

Material untuk langkah ini:

Pelet nilonPelet nilon2 g

Alat yang dibutuhkan:

Mesin cetak injeksiMesin cetak injeksi
Jangka Sorong VernierJangka Sorong Vernier
5

Seat and crimp

Push the collar down onto the recess floor. In the press, squeeze the recess wall inward against the collar and bend its top edge over it.

Alat yang dibutuhkan:

Pres arborPres arbor
6

Try it on a bolt

Screw the nut onto a bolt. It runs freely until the bolt reaches the collar, then turns stiffly as the bolt cuts a thread in the nylon.

Alat yang dibutuhkan:

Baut kepala segi enam - mutu 8.8Baut kepala segi enam - mutu 8.8

Bahan

2

Alat yang Diperlukan

9

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...