Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Rheostat: a Small Ring Rheostat for Toy Motors (Boy Mechanic, 1915)
Emma

Dibuat oleh

Emma

4. November 2026SE
11
0
0
0
0

Rheostat: a Small Ring Rheostat for Toy Motors (Boy Mechanic, 1915)

A small variable resistor to set the speed of a toy motor: resistance wire wound on a fibre strip bent into a ring, set in a groove in a hardwood base, with a brass arm that slides round the bared top of the winding. Wired in series with the motor, it works like a valve in a water pipe. Source: The Boy Mechanic, Book 2 (1915), pp. 393-394. Unknown: wire alloy. Picture: Figs. 1 and 3 of the book.
Menengah
Unknown

Instruksi

1

Wind the resistance strip

Smooth a strip of thin fibre about 1/16 in thick, 1/2 in wide and 10 in long. Wind it with No. 22 cotton-covered resistance wire, close turns from 1/4 in from one end to 1/4 in from the other, securing the ends through small drilled holes and leaving 3 to 4 in free. Bend the strip into a ring round a round object, winding outward, and note its inside and outside diameters.

Material untuk langkah ini:

Bahan tidak diketahuiBahan tidak diketahui1 fibre strip
Kawat resistansi perak JermanKawat resistansi perak Jerman1 No. 22

Alat yang dibutuhkan:

Bor tanganBor tangan
2

Make the base

Round the corners and top edges of a seasoned hardwood block 1/2 x 4 1/2 x 4 1/2 in, mark the ring's two diameters from the centre, and saw out the circles so the ring fits between them. Screw this onto a second board 1/4 x 4 3/4 x 4 3/4 in from below with countersunk screws. Drill a hole for one wire end, fit two back-connected binding posts in the corners, and cut grooves underneath for the leads; one post goes to the winding, the other to the centre bolt.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras2 1/2 and 1/4 in
Sekrup kayuSekrup kayu1 buah
Terminal panelTerminal panel2 buah

Alat yang dibutuhkan:

Jangka tusukJangka tusuk
Gergaji punggungGergaji punggung
Bor tanganBor tangan
Obeng pipihObeng pipih
3

Make and mount the arm

Cut the arm from 1/16 in sheet brass, 2 in long, 1/2 in wide at one end and 1/4 in at the other. Under the narrow end solder thin spring brass to bear on the ring; fit a small handle on top. Mount it on a 1/8 in brass bolt about 1 in long through the centre, with washers under it, the base hole countersunk underneath 1/2 in wide and 1/4 in deep. Solder a short brass strip to the nut, set in a recess, and lock with a second nut or a spring washer.

Material untuk langkah ini:

Lembaran KuninganLembaran Kuningan1 arm, spring
Logam tidak diketahuiLogam tidak diketahui1 1/8 in brass bolt
Ring RataRing Rata3 buah
Spring WasherSpring Washer1 buah
Patri timah-timbalPatri timah-timbal1 buah

Alat yang dibutuhkan:

Gunting sengGunting seng
Bor tanganBor tangan
Solder ListrikSolder Listrik
4

Bare the track and finish

Set the ring in its groove. Sand the insulation off the top edge of the winding so the spring contact touches the wire. Give the wood a coat of shellac.

Material untuk langkah ini:

Pernis sirlakPernis sirlak1 buah

Alat yang dibutuhkan:

AmplasAmplas
Kuas halusKuas halus

Bahan

11

Alat yang Diperlukan

8

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...