Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Ring Stand: a Brass Rod on a Board Foot with Sliding Rings (Faraday, 1830)
Charlie

Dibuat oleh

Charlie

7. November 2026DE
9
0
0
0
0

Ring Stand: a Brass Rod on a Board Foot with Sliding Rings (Faraday, 1830)

A stand that holds flasks and basins at any height over a lamp or furnace. Michael Faraday (1830) describes the retort-stand: an upright brass rod on a heavy foot, with rings of several sizes, each on an arm whose socket slides up and down the rod and is fixed by a screw-nut at the back. Brass feet filled with lead tip over under a heavy vessel, so he makes the foot a stout board about 12 x 6 x 1 inches, the rod fixed 1 1/2 inches from one end, and stands the lamp or furnace on the board under the ring. Source: M. Faraday, Chemical Manipulation (1830), §386, p. 175. Picture: his woodcut.
Pemula
Unknown

Instruksi

1

Read Faraday

"It is much better to make the foot of a piece of stout board, about twelve inches in length, six inches in width, and an inch thick. The upright rod should be fixed about one inch and a half from one end of it, the lamp or furnace should be placed upon it, and the ring of course in a corresponding direction. Such an arrangement is perfectly steady, and cannot be overset by any weight which it is strong enough to bear."
2

Fix the rod in the board

Take a stout board about 12 in. long, 6 in. wide and 1 in. thick. Fix an upright brass rod in it about 1 1/2 in. from one end. Rod size, and how it is fixed, are not given (unknown). Ours: a hardwood board.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 kaki
Batang KuninganBatang Kuningan1 upright
Konektor tidak diketahuiKonektor tidak diketahui1 buah

Alat yang dibutuhkan:

Dimensi tidak diketahuiDimensi tidak diketahui
3

Make the rings

Make several rings of different sizes, each fixed to an arm, and each arm to a socket that slides freely up and down the rod. Fit each socket with a screw-nut at the back to tighten it at any height. The metal and sizes are not given (unknown). Ours: wing nuts for the screw-nuts.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 rings, arms, sockets
Mur sayapMur sayap1 buah

Alat yang dibutuhkan:

Dimensi tidak diketahuiDimensi tidak diketahui
4

Use it

Stand the lamp or furnace on the board and turn the ring over it. Slide the ring to the height wanted and tighten the screw. Do not set a hot flask on a cold ring, or a cold, freshly filled flask on a hot ring over the fire: the bottom may come out (Faraday §388).

Bahan

5

Alat yang Diperlukan

1

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...