Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Small Series-Wound Electric Motor with Laminated Field and 12-Slot Ring Armature (Robertson, Boy Mechanic 1913)
Volt

Dibuat oleh

Volt

14. November 2026SE
9
0
0
0
0

Small Series-Wound Electric Motor with Laminated Field and 12-Slot Ring Armature (Robertson, Boy Mechanic 1913)

A real workshop-built DC motor: a field of riveted sheet-iron plates bored to 2-3/4 in, a 12-slot laminated ring armature on a brass spider, a 12-segment brass commutator insulated with mica, gauze brushes, and series windings of cotton-covered magnet wire.
Lanjutan
Several weekends

Instruksi

1

Read the Boy Mechanic

"The field frame of the motor, Fig. 1, is composed of wrought sheet iron."
2

Field frame

Mark a template 1/16 in larger than Fig. 1, cut enough sheet-iron plates to make 3/4 in, drill four rivet holes and rivet them. Mark the bore with dividers set at 1/8 in, drill 1/4 in holes round it and file to shape. Bore to 2-3/4 in on a lathe; mark the field core at 3-3/8 in and the outside at 4-1/2 in and finish to the marks.

Material untuk langkah ini:

Pelat Baja LunakPelat Baja Lunak1 buah
Paku keling bajaPaku keling baja1 buah

Alat yang dibutuhkan:

PenggoresPenggores
Jangka tusukJangka tusuk
Bor tanganBor tangan
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Mesin Bubut LogamMesin Bubut Logam
PaluPalu
3

Studs, lugs and bearings

Drill and tap two 3/8 in holes 3-5/8 in apart for the bearing studs (Fig. 2) and 1/4 in holes for feet bent from 1/8 in brass or iron. Make the bearing supports from 1/8 in brass with a 5/8 in hole and a 5/8 in brass rod soldered in and drilled for the shaft. Fit them after the armature is made: wrap paper round the armature, set it in the field, slip the bearings on and solder them, then check it turns freely.

Material untuk langkah ini:

Lembaran KuninganLembaran Kuningan1 buah
Batang KuninganBatang Kuningan1 buah
Batang bulat baja lunakBatang bulat baja lunak1 buah
Patri timah-timbalPatri timah-timbal1 buah

Alat yang dibutuhkan:

Set pembuat ulirSet pembuat ulir
Mesin Bubut LogamMesin Bubut Logam
SolderSolder
Bor tanganBor tangan
4

Armature core

Cut two 1/8 in wrought-iron outer plates and enough No. 24 sheet iron to make over 3/4 in (Fig. 5), drill six 1/8 in holes and rivet. Anneal at cherry red and cool in ashes. Bore to 1-11/16 in, fit a brass spider turned from 3/4 in brass on the machine-steel shaft with a setscrew, solder, turn the outside and face it to 3/4 in. File 12 slots 1/4 in deep and 7/16 in wide.

Material untuk langkah ini:

Pelat Baja LunakPelat Baja Lunak1 buah
Paku keling bajaPaku keling baja1 buah
Batang KuninganBatang Kuningan1 buah
Batang bulat baja lunakBatang bulat baja lunak1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Mesin Bubut LogamMesin Bubut Logam
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Bor tanganBor tangan
5

Commutator

Turn a piece of 3/4 in i.d. brass pipe to 3/4 in long, chamfer both ends at 60 deg, divide into 12, drill and tap a 1/8 in hole in each segment for a brass pin, turn the pins to 1-1/4 in outside and slit them for the wires. Saw it into 12 bars, fit them on turned fibre ends with 12 mica strips between, clamp with the nut and true up.

Material untuk langkah ini:

Tabung kuninganTabung kuningan1 buah
Batang KuninganBatang Kuningan1 buah
Lembaran fiber vulkanisirLembaran fiber vulkanisir1 buah
Lembaran mikaLembaran mika1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Set pembuat ulirSet pembuat ulir
Gergaji BesiGergaji Besi
6

Brushes

Make the brush holder of fibre (Fig. 8) and studs of 5/16 in brass rod (Fig. 9). Roll brass or copper wire gauze and flatten it to 1/8 x 1/4 in, solder one end, and fit the holder on the bearing with a setscrew.

Material untuk langkah ini:

Lembaran fiber vulkanisirLembaran fiber vulkanisir1 buah
Batang KuninganBatang Kuningan1 buah
Anyaman kawatAnyaman kawat1 buah
Patri timah-timbalPatri timah-timbal1 buah

Alat yang dibutuhkan:

SolderSolder
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
7

Wind the field

Insulate the field cores with 1/64 in fibre and end washers 1-1/8 x 1-1/2 in (softened in warm water, then glued). Wind each side with four layers (about 50 ft) of No. 18 double-cotton-covered wire, A to B and C to B, and join the ends at B.

Material untuk langkah ini:

Lembaran fiber vulkanisirLembaran fiber vulkanisir1 buah
Kawat Tembaga Berlapis EmailKawat Tembaga Berlapis Email1 buah
Lem KayuLem Kayu1 buah
8

Wind the armature

Line the ring and spider with 1/16 in fibre and the slots with 1/64 in fibre channels. Wind each slot with about 12 ft of No. 21 wire, 40 turns in four layers of 10, shellacking each layer, leaving 2 in ends. Join each coil's start to the next coil's finish and solder the joints to the commutator pins.

Material untuk langkah ini:

Lembaran fiber vulkanisirLembaran fiber vulkanisir1 buah
Kawat Tembaga Berlapis EmailKawat Tembaga Berlapis Email1 buah
Pernis sirlakPernis sirlak1 buah
Patri timah-timbalPatri timah-timbal1 buah

Alat yang dibutuhkan:

SolderSolder
9

Mount and wire

Screw the motor to a wood base 8 x 6 x 1 in with two terminals and a switch. Wire it in series: field end A to a terminal, field end C to one brush stud, the other brush through the switch to the other terminal.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah
Terminal panelTerminal panel1 buah
Sakelar tuasSakelar tuas1 buah
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Bor engkol dan mata borBor engkol dan mata bor
10

Troubleshooting

Motor troubleshooting.

Flow

Loading...
11

History and honest limits

From W. A. Robertson in **The Boy Mechanic, Book 1** (Popular Mechanics, 1913), pp. 345-347 (checked on the archive.org scan boymechanic0000unse_n5a8). Sizes not in the text are in his Figs. 1-9; enamelled wire for cotton-covered and the low-voltage advice are ours.

Bahan

17

Alat yang Diperlukan

11

Cetak biru ini membuat

Blueprint terkait

Blueprint ini berbagi pengetahuan โ€” teknik, bahan, atau prinsip

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...