SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Rocking Twin-Dasher Lever Churn: One Lever Rocks the Box and Works Two Dashers Through a Perforated Wall
Millie

Dibuat oleh

Millie

7. Oktober 2026NL
9
0
0
0
0

Rocking Twin-Dasher Lever Churn: One Lever Rocks the Box and Works Two Dashers Through a Perforated Wall

A. C. Stiles of South Bloomfield, Ohio, received US 3,764, dated 27 September 1844, for a rocking churn: an oblong box on rockers, split by a partition with holes, with a dasher on each side worked by arms on shafts across the ends, and one upright lever that rocks the box and works the dashers together. This rung prints the partition, dashers and arms, builds the box and makes butter.
Lanjutan
About 6 hours, plus printing

Instruksi

1

One lever, three motions

Memuat notebook Jupyter…
2

Two dashers from one lever, before it

Mitchell worked two dashers from one lever; Stiles adds rockers and a perforated partition between them.
3

Read US 3,764

"The machine is operated by moving the upright lever l, to and fro, which rocks the box, while at the same time it works the dashers up and down, thus throwing the cream through the partition d, till the butter is made."
4

Print the parts

Print the partition (/uploads/blueprints/rocking-twin-dasher-lever-churn-partition.stl), two dashers (/uploads/blueprints/rocking-twin-dasher-lever-churn-dasher.stl), two dasher arms (/uploads/blueprints/rocking-twin-dasher-lever-churn-dasher-arm.stl) and two lower arms (/uploads/blueprints/rocking-twin-dasher-lever-churn-lower-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.

Material untuk langkah ini:

Filamen PETGFilamen PETG1 buah

Alat yang dibutuhkan:

Pencetak 3D filamen (FDM)Pencetak 3D filamen (FDM)
5

Box on rockers

Build a pine box about 260 × 120 × 150 mm with a close-fitting lid, sealed inside. Glue the partition across its middle and screw two curved pine rockers lengthwise underneath. Drill the lid for the two dasher handles.

Material untuk langkah ini:

Papan pinusPapan pinus1 buah
Lem KayuLem Kayu1 buah
Sealant SilikonSealant Silikon1 buah
Sekrup kayu #8 x 1"Sekrup kayu #8 x 1"1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Gergaji CopingGergaji Coping
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
KlemKlem
6

Shafts, arms and lever

Set a 10 mm square shaft across each end on two studs, 60 mm above the lid. Fit a dasher arm on each, pointing inward and pinned to its dasher's handle, and a lower arm on each outside the box. Join the lower arms with a pine bar, and pivot an upright pine lever on a block near the box's foot, pinned to the bar's middle.

Material untuk langkah ini:

Pasak kayu kerasPasak kayu keras1 buah
Papan pinusPapan pinus1 buah
Batang Baja LunakBatang Baja Lunak1 buah
Sekrup mesinSekrup mesin1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Set obengSet obeng
7

The patent drawing

US 3,764 drawing sheet, public domain (expired patent).
Langkah 7 - Image 1
8

Rock and churn

Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Work the lever to and fro: the box rocks and the dashers rise and fall in turn. Keep fingers clear of the arms and the rockers. Time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.

Material untuk langkah ini:

Krim kentalKrim kental1500 ml
Garam Laut KasarGaram Laut Kasar1 buah
AirAir1 buah

Alat yang dibutuhkan:

Termometer probe tinggal-pasangTermometer probe tinggal-pasang
StopwatchStopwatch
Timbangan Dapur DigitalTimbangan Dapur Digital
Mangkuk aduk baja nirkarat (besar)Mangkuk aduk baja nirkarat (besar)
9

Troubleshooting

Rocking twin-dasher churn troubleshooting.

Flow

Loading...
10

History and honest limits

**A. C. Stiles** of South Bloomfield, Pickaway County, Ohio, US 3,764, 27 September 1844. He claimed the combination of the rockers and dashers in the double-chambered churn. His drawing gives no sizes; ours are ours. FDM prints hold food in their layer lines, so wash well and replace when worn.

Bahan

11

Alat yang Diperlukan

11

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...