SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Rubber Squeeze Bulb: Latex Coagulated Inside a Split Mould Coated with Calcium Nitrate (Szegvari, Anode, US 1,949,502)
A seamless hollow rubber bulb grows inside a closed mould: the cavity is coated with a coagulant, the mould is filled with latex, and rubber sets on the walls until it is thick enough. The rest of the latex is poured out through the neck.
Result: a seamless rubber squeeze bulb with a neck; ours sized at about 60 ml.
Source: Szegvari, US 1,949,502 (American Anode, 1934); his example is a football bladder. Not given: times, strengths, vulcanising details. Picture drawn by Youblob.
Menengah
2 days
Instruksi
1
1
Coat the mould cavity with calcium nitrate in acetone
Coat the mould cavity with calcium nitrate in acetone
Open the split mould and coat only the cavity with a solution of calcium nitrate in acetone, by brush or spray. The acetone evaporates and leaves a sticky film of coagulant. Ours: a cavity of about 60 ml with a neck.
Alat yang dibutuhkan:
Kalsium nitrat
Aseton
Cetakan bola belah dua
Kuas lebar2
2
Close the mould under the latex
Close the mould under the latex
Lower both halves under the surface of latex and close them once they are submerged and the air bubbles are gone. Rubber now sets on the coated walls; the longer the contact, the thicker the wall.
Material untuk langkah ini:
Lateks karet alam1 as requiredAlat yang dibutuhkan:
Panci Besar3
3
Pour out the extra latex through the neck
Pour out the extra latex through the neck
Lift the mould out and turn it over so the liquid latex drains back through the neck. Refill with water holding a little acetic acid so the inner face sets too.
Alat yang dibutuhkan:
Asam asetat (glasial)
Air4
4
Open under warm water and leach
Open under warm water and leach
Open the mould under running warm water, take out the bulb and leave it in the water until most of the soluble matter has leached out. Clean any liquid latex off with dilute ammonia.
Alat yang dibutuhkan:
Air
Larutan amonia encer5
5
Inflate lightly and dry
Inflate lightly and dry
Drain the bulb, inflate it lightly so it does not collapse, and dry it at room temperature or in a drying cabinet. The latex may hold sulphur and be vulcanised in the usual way; Szegvari gives no details.
Alat yang dibutuhkan:
Oven pengeringanBahan
1- 1 as requiredPlaceholder
Alat yang Diperlukan
9- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Cetak biru ini membuat
Blueprint terkait
Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip
CC0 Domain Publik
Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.
Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.