Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Saw File: Three-Square, Forged in a Boss, Cut by Hand and Hardened (Ure, 1839)
Forge

Dibuat oleh

Forge

4. November 2026NO
24
0
0
0
0

Saw File: Three-Square, Forged in a Boss, Cut by Hand and Hardened (Ure, 1839)

The file for sharpening saw teeth as Sheffield made it by hand: a three-square (triangular) bar of cast steel, not tapering, forged in a V-shaped boss, its teeth cut one by one with a chisel and hammer, then hardened under a coat of animal carbon and salt and quenched in cold spring water. Ure says saw files in particular should be hardened with the carbon mixture, so they will cut iron and steel. Not given: sizes and teeth per inch. Source: A. Ure, Dictionary of Arts, Manufactures, and Mines (1839), File. Picture: our drawing.
Lanjutan
Unknown

Instruksi

1

Forge the blank

Draw cast steel out square at the forge, then lay it with one angle down in a boss whose recess has two sides meeting at an angle, so the hammer forms one side and the boss the other two. Keep it the same size along its length (saw files are not tapered).

Material untuk langkah ini:

Baja krusibelBaja krusibel1 cast steel bar
Dimensi tidak diketahuiDimensi tidak diketahui1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Penjepit TempaPenjepit Tempa
Swage bawahSwage bawah
PaluPalu
GodamGodam
2

Cut the teeth

On an anvil with a flat, even face, hold the file down with a leather strap over each end, the workman's feet in the straps like stirrups. Cut the teeth with a chisel a little broader than the file, sharpened to about 20 degrees, struck with a hammer of 1 to 6 lb. For single cut, run a fine file lightly over the teeth to take off the roughness; for double cut, cut a second set nearly at right angles to the first.

Alat yang dibutuhkan:

Landasan tempa bajaLandasan tempa baja
Tali KulitTali Kulit
Pahat besi dinginPahat besi dingin
PaluPalu
Kikir LogamKikir Logam
3

Cut the other sides

To cut the next side, lay the file in a piece of lead-tin alloy with an angular groove, so the teeth already cut are not spoiled on the anvil.

Alat yang dibutuhkan:

Patri timah-timbalPatri timah-timbal
Landasan tempa bajaLandasan tempa baja
Pahat besi dinginPahat besi dingin
PaluPalu
4

Coat for hardening

Distil shoemakers' and curriers' leather refuse in an iron still and powder the bright coal left. Grind about equal parts by bulk of this carbon and salt to the consistence of cream with water and cover the file with it.

Alat yang dibutuhkan:

Retort besiRetort besi
GaramGaram
AirAir
5

Harden

Hold the file by the tang in a fire of very small cokes, drawing it out often, until it is an even cherry red from tang to point. Plunge it straight down, quickly, into clear spring water as cold as possible.

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Kokas metalurgiKokas metalurgi
Penjepit TempaPenjepit Tempa
AirAir
6

Clean and oil

Brush the file with water and powdered cokes until clean and metallic, wash it in two or three waters to take off all the salt, dip it in lime-water, dry it quickly before the fire and oil it while warm with olive oil containing a little oil of turpentine.

Alat yang dibutuhkan:

Kokas metalurgiKokas metalurgi
AirAir
Air kapurAir kapur
Minyak zaitunMinyak zaitun
TerpentinTerpentin

Bahan

2

Alat yang Diperlukan

17

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...