Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Renewable Rubber-Face Hammer: Rolled Faces Pressed Onto Pronged Discs, Driven Out Through a Notch When Worn (Sewell, 1928)
Forge

Dibuat oleh

Forge

13. November 2026NO
10
0
0
0
0

Renewable Rubber-Face Hammer: Rolled Faces Pressed Onto Pronged Discs, Driven Out Through a Notch When Worn (Sewell, 1928)

Albert G. Sewell received US 1,674,999, dated 26 June 1928, for a soft-face hammer whose worn faces can be renewed instead of throwing the hammer away. Each end of the head is a cup. A face rolled from a strip is pressed into the cup onto a loose sheet-metal disc whose prongs bite into it and wedge it tight. When a face is battered, a rod pushed through a notch at the bottom of the cup drives the disc and the face out together, and a new face goes in. He preferred rawhide and named rubber among face materials; ours are rolled from rubber sheet. The patent gives no sizes; every size here is ours.
Menengah
About 1 day

Instruksi

1

Rolling a face plug

Memuat notebook Jupyter…
2

Read US 1,674,999

"Thus, by hammering or otherwise thrusting a rod or suitable device against the wedging member, the latter, with the striking face member, can be forced or driven out of the socket or recess, after which a new striking face member may be forced into the socket, to be secured therein by the wedging member."
3

Turn the head

Grip 40 mm steel round bar in the chuck and turn a head 110 mm long: the two ends stay 40 mm across for 26 mm as the flanges D, and the middle is waisted to 30 mm. Bore each end 32 mm across and 22 mm deep for the sockets C, flat at the bottom. Drill a 20 mm eye B through the middle, square to the axis, in a V-block on the drill press.

Material untuk langkah ini:

Batang bulat baja lunakBatang bulat baja lunak1 buah
Minyak potongMinyak potong1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Cekam bubut 3 rahangCekam bubut 3 rahang
Pahat bubutPahat bubut
Batang bor dalamBatang bor dalam
Pahat potong bubutPahat potong bubut
Mesin Bor DudukMesin Bor Duduk
Blok VBlok V
Set Mata BorSet Mata Bor
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
Kacamata pengamanKacamata pengaman
4

Cut the notches K

On the handle's side of each flange, saw and file a notch 8 mm wide through the flange's wall at the very bottom of the socket, so a rod can be pushed in at a slant against the edge of the disc at the bottom.

Alat yang dibutuhkan:

Ragum MejaRagum Meja
Gergaji BesiGergaji Besi
Set KikirSet Kikir
PenitikPenitik
5

Pronged discs G

Cut two discs of 1.5 mm steel sheet 31.5 mm across. At four places round each rim, snip two cuts 6 mm deep 5 mm apart and bend the tab between them up at a right angle with the pliers: the prongs H. Drop one disc loosely into the bottom of each socket, prongs out.

Material untuk langkah ini:

Pelat Baja LunakPelat Baja Lunak1 buah

Alat yang dibutuhkan:

Gunting sengGunting seng
Tang Berujung RataTang Berujung Rata
Ragum MejaRagum Meja
Set KikirSet Kikir
6

Roll and press in the faces E

Cut two strips of 3 mm natural rubber sheet 32 mm wide and about 270 mm long. Roll each tightly into a coil, trimming the strip until the coil just enters a socket, and tie it. Press the coil into its socket in the vice, between soft packing, until it bottoms on the disc and its prongs bite in, leaving the face standing about 10 mm out. Cut the tie and trim the face flat with the knife.

Material untuk langkah ini:

Lembaran karet alamLembaran karet alam1 buah

Alat yang dibutuhkan:

Pisau KerajinanPisau Kerajinan
Ragum MejaRagum Meja
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
7

Handle

Turn an ash handle 300 mm long, its end a tight fit in the eye. Saw a slot down its end, drive it into the eye, and glue and drive a hardwood wedge into the slot; saw it off flush.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah
Lem KayuLem Kayu1 buah

Alat yang dibutuhkan:

Mesin bubut kayuMesin bubut kayu
Set pahat bubut (HSS)Set pahat bubut (HSS)
Gergaji BesiGergaji Besi
Palu kepala bulatPalu kepala bulat
8

Renew a face

When a face is worn, push a steel rod through the socket's notch against the disc's edge and tap it out with the hammer; the disc and the face come out together. Put the disc back, prongs out, and press in a new rolled face.

Alat yang dibutuhkan:

Palu kepala bulatPalu kepala bulat
Ragum MejaRagum Meja
9

Troubleshooting

Soft-face hammer troubleshooting.

Flow

Loading...
10

History and honest limits

**Albert G. Sewell**, US 1,674,999, dated 26 June 1928, filed 25 July 1927. He describes a head with a socket at each end formed by annular flanges, a striking face member of relatively soft material rolled from a strip and pressed in as a plug, a loose sheet-metal wedging disc with prongs in the socket's bottom, and openings through which a rod drives the disc and face out. He preferred rawhide and his head was cast iron; ours is turned steel with faces rolled from rubber sheet, which he lists among the face materials in use. He gives no sizes; every size here is ours.

Bahan

6

Alat yang Diperlukan

20

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...