Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI

Steam Boiler: Small Brass Shell Boiler, Screwed and Soldered (Hopkins, Model Engines and Small Boats, 1898)
A small steam boiler for model engines and boats: a brass cylinder 4 in across, closed by two brass heads tied together by a brass stay rod, its seam held by two rows of brass screws and sealed with solder. It sits in a russia-iron jacket over an alcohol lamp, with a weighted safety valve and fusible plugs that put the lamp out if the water runs low.
Result: a strong little shell boiler, 6 to 12 in long to suit the engine.
Source: N. M. Hopkins, Model Engines and Small Boats (1898), ch. III. Unknown: the working pressure and the valve's sizes. Picture: the book's Fig. 33.
Menengah
Unknown
Instruksi
1
1
Make the heads and stay
Make the heads and stay
Cut two brass disks 4 in across and about 1/8 in thick, each with a 1/4 in hole in the centre, and true them up in the lathe. Pass a 1/4 in brass rod through both and solder it, with plenty of solder inside the heads to make them steam-tight. Screw heavy brass disks (round nuts are better than square) onto the rod ends against the heads. Set the heads 10 in apart over their outsides; about 6 in will do for a small single-acting engine, 7 in for a double engine, up to 12 in for a larger one.
Material untuk langkah ini:
Batang Bulat Kuningan1 two heads, two nuts
Batang Kuningan1 1/4 in stay
Patri timah-timbal1 as needed
Fluks1 as neededAlat yang dibutuhkan:
Mesin Bubut Logam
Pembakar Bunsen2
2
Roll and screw the shell
Roll and screw the shell
Cut soft sheet brass at least 1/32 in thick (1/16 in for boilers over 8 in long), about 14 in long and 1/2 in longer than the heads so it overhangs 1/4 in each end. Roll it round the heads on tinner's rollers, never by hand, so it laps about 1 in. Slip it over the heads and rod and bind it tight with heavy twine. Drill two rows of holes along the lap, tap them and turn in little brass screws that go just through the under plate without projecting. Do not use iron screws: their rust pits the seams.
Material untuk langkah ini:
Lembaran Kuningan1 shell
Sekrup mesin1 small brass screws
Tali pengikat1 bindingAlat yang dibutuhkan:
Mesin rol pelat
Bor tangan
Set pembuat ulir3
3
Solder it up
Solder it up
Push the heads and rod out, hold the shell in a Bunsen flame and run solder well along the seam. Push the heads back and solder them all round the edge, and screw the nuts tight: the screws and stay take the strain, the solder keeps in the steam. Drill two or three 1/4 in holes in the top and bush them with heavy brass disks soldered on. For fusible plugs, drill two 1/4 in holes near the bottom and solder them shut with little brass caps.
Material untuk langkah ini:
Patri timah-timbal1 as needed
Fluks1 as needed
Batang Bulat Kuningan1 bushes and plug capsAlat yang dibutuhkan:
Pembakar Bunsen
Bor tangan4
4
Fit the jacket and safety valve
Fit the jacket and safety valve
Cut end supports from russia sheet iron to hold the boiler by its ends, with an opening for the alcohol lamp, and bend a russia-iron cover over it, riveted to the ends by little ears. Punch a row of small holes along the cover's lower edge to let air in for the lamp; the cover keeps in the heat and keeps draughts off the flame. Turn a small safety valve true in the lathe, grind it to its seat with emery and oil, and fit a lead weight on its bar. Not given: the valve's sizes.
Material untuk langkah ini:
Lembaran besi Rusia1 ends and cover
Paku keling besi1 small
Batang Bulat Kuningan1 valve
Timbal1 weightAlat yang dibutuhkan:
Gunting seng
Set keling
Mesin Bubut Logam
Kain emeri5
5
Fire and set it
Fire and set it
Fill the boiler two-thirds full, connect the engine and light the alcohol lamp under it. If the valve blows off before the engine turns over, move the weight a little farther out until the engine runs without steam escaping; well made, the valve will then blow off soon after the engine stops if the fire is left. If the water ever runs very low, the fusible plugs melt and the steam puts out the lamp. Do not try to burst a boiler to test it.
Alat yang dibutuhkan:
Pembakar spiritusBahan
10- 1 valvePlaceholder
- 1 1/4 in stayPlaceholder
- 2 as neededPlaceholder
- 2 as neededPlaceholder
- 1 shellPlaceholder
- 1 small brass screwsPlaceholder
- 1 bindingPlaceholder
- 1 ends and coverPlaceholder
- 1 smallPlaceholder
- 1 weightPlaceholder
Alat yang Diperlukan
9- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Bahan cetak biru terhubung
Cetak biru ini membuat
CC0 Domain Publik
Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.
Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.


