Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)
Woody

Dibuat oleh

Woody

13. November 2026NO
7
0
0
0
0

16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)

Stillman Taylor's open Canadian canoe from The Boy Mechanic, Book 3 (1919): about 16 ft long, 31 in beam, 60 to 70 lb. Built upside down over a backbone and seven paper-pattern molds, with oak or ash stems, keelson and gunwales, 1/8 in cedar ribs and planking fastened with copper clout nails, then covered with No. 6 canvas laid in melted marine glue, painted, and varnished. Every layout dot and width is his, as printed.
Lanjutan
Several weeks

Instruksi

1

His layout data

Memuat notebook Jupyter…
2

Read The Boy Mechanic, Book 3

"Working with light materials, the canoe builder must pay particular attention to the workmanship ... the work must not be hurried, but plenty of time taken to do each and every part well."
3

Get the materials

Stem: oak or ash 6 ft x 3/4 in square. Keelson: oak or ash 14 ft x 3-1/2 x 3/8 in. Gunwales: 2 of oak or ash 16 ft x 7/8 x 1/2 in. Seat risings: 2 of oak or ash 1/2 in square. Fenderwales: 34 ft of 1/2 in half-round molding. Outside keel (optional): oak 14 ft x 1 x 1/2 in. Deck beams: 2 of oak or ash 8 x 1-1/8 x 3/8 in. Seat frames: 2 at 30 x 3 x 3/4 and 2 at 12 x 2-1/4 x 3/4 in. Planking: cedar or pine, 100 sq ft, 1/8 in (25 ft of 1 in lumber dressed to 1/8 in, in 12, 14 and 16 ft lengths). Ribs: 360 running ft of cedar 1-3/4 x 1/8 in. Breast hooks: cedar or oak 32 x 9 x 3/4 in. Backbone, molds and ribbands from any cheap stuff. Fastenings: 1 lb 2 in wire nails; 1 lb 5/8 in and 1/2 lb 3/4 in copper clout nails; 18 brass screws 1-1/4 in No. 8 and 24 brass screws 1 in No. 6; 4 lb marine glue; 3 oz No. 2 copper tacks; 11-3/4 yd No. 6 canvas; 1 lb 3/8 in copper tacks. Rock elm or fir may replace oak or ash; spruce, pine, cypress or fir may replace cedar.

Material untuk langkah ini:

Papan ek putihPapan ek putih4 buah
Papan kayu cedarPapan kayu cedar6 buah
Papan pinusPapan pinus3 buah

Alat yang dibutuhkan:

Gergaji belahGergaji belah
Gergaji TanganGergaji Tangan
Ketam tanganKetam tangan
Meteran GulungMeteran Gulung
4

Lay out the backbone and molds

Cut the backbone from a 16 ft x 4 x 7/8 in board, top edge 15 ft 8-3/4 in, and mark the mold stations from each end: 22-1/4 in to mold 1, then 23-1/4 in to mold 2 and 23-1/4 in to mold 3, each mold space 3/4 in thick; mold 4 sits at the centre; cut the ends off on the bevel (Fig. 1). Draw each mold on stiff paper from his rectangles, mortises and dots (notebook), trace the curve through the dots, cut out the half, fold and draw the other side, and cut the molds from 7/8 in stock: seven in all, numbered alike from each end: two No. 1, two No. 2 (each in halves), two No. 3 and one No. 4; nail battens across the halves.

Material untuk langkah ini:

Papan pinusPapan pinus2 buah
Lembar kertas tebalLembar kertas tebal1 buah
PakuPaku1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Gergaji CopingGergaji Coping
PenggarisPenggaris
PensilPensil
GuntingGunting
PaluPalu
5

Bend the stems and shape the keelson

Make the stem mold from his Fig. 6 pattern (24-1/2 x 12 in rectangle, dots in the notebook) and bend the straight-grained 3/4 in square oak or ash stems on it. Cut the keelson 13 ft 11 in long, tapering from 3-1/2 in at the centre: 3-1/2 in at 1 and 2 ft, 3-1/4, 2-5/8, 2 and 1-1/4 in at 3 to 6 ft, and 15/16 in at the ends (Fig. 7). Fasten each stem to the keelson with a couple of 3/4 in No. 10 screws.

Material untuk langkah ini:

Papan ek putihPapan ek putih2 buah
Sekrup kayu kuninganSekrup kayu kuningan4 buah

Alat yang dibutuhkan:

Pisau TarikPisau Tarik
Ketam tanganKetam tangan
Gergaji TanganGergaji Tangan
Bor engkol dan mata borBor engkol dan mata bor
Obeng pipihObeng pipih
Klem CKlem C
6

Set up the frame

Build it upside down: set the backbone on boxes about 1 ft or more off the floor and the molds in their numbered places, the backbone resting in their top mortises. True the molds with a square and toenail them. Lay the keelson in its mortises, fit the stems to the backbone angle and nail through the mold tops into them. Bevel the stem splice from the inside, leaving the outer edge about 1/8 in wide. Put on the gunwales at the sheer line with nails left proud, then four ribbands a side at 5 in centres from the keel, fastened with 1-1/4 in brads.

Material untuk langkah ini:

Papan ek putihPapan ek putih2 buah
Papan pinusPapan pinus1 buah
PakuPaku1 buah

Alat yang dibutuhkan:

Siku-siku tetapSiku-siku tetap
PaluPalu
Pahat kayuPahat kayu
Ketam tanganKetam tangan
7

Rib the hull

Saw cedar ribs 1-3/4 in wide and 1/8 in thick, cut to length gunwale to gunwale over the ribbands. Space them 3 in apart on centres along the keelson, one over each mold. Fasten each rib to the outside of the keelson with two 5/8 in copper clout nails, spring it in under the ribbands and fasten it to the gunwales. Then remove the ribbands.

Material untuk langkah ini:

Papan kayu cedarPapan kayu cedar2 buah
Paku tembaga kepala lebarPaku tembaga kepala lebar1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
PaluPalu
Meteran GulungMeteran Gulung
8

Plank the hull

Plank with 1/8 in cedar, bent cold, full length stem to stem, butted edge to edge without bevel, about 3 in wide; begin with the garboard strake at the keel and end with the sheer strake level with the gunwale. Punch nail holes with an awl, staggered along the ribs; clamp the plank, drive copper clout nails and clinch them inside on a clinch iron. Trim the plank ends to the stems and gunwales, saw the backbone in two to take out the frame, tack strips across the gunwales against sagging, and nail where the molds were.

Material untuk langkah ini:

Papan kayu cedarPapan kayu cedar4 buah
Paku tembaga kepala lebarPaku tembaga kepala lebar1 buah
Paku payung tembagaPaku payung tembaga1 buah

Alat yang dibutuhkan:

Penusuk (Uncek)Penusuk (Uncek)
Klem CKlem C
Besi penahan pakuBesi penahan paku
PaluPalu
Gergaji TanganGergaji Tangan
9

Fit risings, seats, decks and thwarts

Nail 1/2 in square oak or ash seat risings, 14 ft long, about 4 in below the gunwale, boring first and clinching inside. Make the seat frames as Fig. 10 and cane them or tack on canvas (a kneeling paddler may use a 4 or 5 in seat bar instead). Notch the 8 x 1-1/8 x 3/8 in deck beams to wedge about 1/2 in against the gunwales (Fig. 11) and fix each with a 1-1/4 in No. 10 screw through the gunwale. Shape the decks 16 x 8 in (Fig. 12) and fix them with three 1-1/4 in No. 10 screws into the beam and three along each gunwale. Screw a centre thwart of oak or ash, 3/8 in thick, 2 in tapering to 1 in, under the gunwales amidships; extra thwarts behind the forward seat and about 3 ft forward of the rear seat stiffen it.

Material untuk langkah ini:

Papan ek putihPapan ek putih2 buah
Papan kayu cedarPapan kayu cedar1 buah
Paku tembaga kepala lebarPaku tembaga kepala lebar1 buah
Sekrup kayu kuninganSekrup kayu kuningan30 buah
Kain kanvasKain kanvas1 buah

Alat yang dibutuhkan:

Bor engkol dan mata borBor engkol dan mata bor
Obeng pipihObeng pipih
Gergaji TanganGergaji Tangan
Pahat kayuPahat kayu
PaluPalu
10

Lay the canvas

Lay the No. 6 canvas smoothly on the hull and trim it to fold at the stems (Fig. 13). Melt the black marine glue in a can over a moderately hot fire and spread a fairly heavy coat over one side of the canvas with a stiff brush. Lay it on and iron it with a moderately hot flatiron so the glue melts into the planking. Tack the edges along the gunwales and fold the canvas smoothly at the stems, tacking exactly down the stem centre line.

Material untuk langkah ini:

Kain kanvasKain kanvas1 buah
Lem perahu (marine glue)Lem perahu (marine glue)1 buah
Paku payung tembagaPaku payung tembaga1 buah

Alat yang dibutuhkan:

KalengKaleng
Kuas lebarKuas lebar
Setrika besiSetrika besi
GuntingGunting
PaluPalu
11

Fenders, stem bands and keel

Tack 1/2 in round molding over the canvas edge (or a 1 in strip of planking with 1-1/4 in brads every 2 or 3 in). Put on stem bands of wood about 3/8 in square, rounded, with 1-1/4 in brads, or better, 3/8 in brass oval stem band with 3/4 in screws. An outside keel is optional: about 1 x 1/2 in of oak or ash tapered to the stem bands, or a flat keel about 2-1/2 in wide of 3/8 in oak or ash, which turns more easily and guards the bottom.

Material untuk langkah ini:

List kayu setengah bulatList kayu setengah bulat1 buah
Pelat kuningan haluanPelat kuningan haluan2 buah
Sekrup kayu kuninganSekrup kayu kuningan12 buah
Papan ek putihPapan ek putih1 buah
PakuPaku1 buah

Alat yang dibutuhkan:

PaluPalu
Obeng pipihObeng pipih
Ketam tanganKetam tangan
Bor tanganBor tangan
12

Paint and finish

Give the canvas a coat of shellac to waterproof it, then four coats of paint to fill the fibres, rubbing down the second and third with fine sandpaper. Finish all woodwork with three coats of good outside spar varnish. A removable slatted grating of soft-pine lattice, about 1-1/8 in wide and 1-1/4 in thick as printed, screwed to curved cross strips (not the ribs), protects the bottom.

Material untuk langkah ini:

Pernis sirlakPernis sirlak1 buah
Cat minyakCat minyak1 buah
AmplasAmplas1 buah
Pernis tiang kapalPernis tiang kapal1 buah
Papan pinusPapan pinus1 buah

Alat yang dibutuhkan:

Kuas lebarKuas lebar
Obeng pipihObeng pipih
13

Troubleshooting

Canoe troubleshooting.

Flow

Loading...
14

History and honest limits

From "How to Build a Canoe, Part I" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 77-84). As printed, his text differs in places: the backbone's lower edge is 1/2 in longer in one sentence and 1 in in the next; the list gives No. 8 deck screws, the text No. 10; the list's seat frames (30 x 3 and 12 x 2-1/4 in) differ from Fig. 10 (29 x 9 in); the fenders are half-round in the list and round in the text. The metric figures are ours.

Bahan

16

Alat yang Diperlukan

21

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...