SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI

The Cam-Lever Lemon Squeezer: A Cam on a Shaft Presses the Plunger, Springs Lift It
A plunger pressed straight down by the hand needs a strong push to empty a lemon.
A. Clarence Weeks of New York received US 165,638, dated 13 July 1875, for a squeezer with a frame on legs over a dish, a perforated bowl in the frame, a plate hinged to one end carrying the plunger, two standards on the frame with a shaft across them carrying "a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger", and springs from the plate to the standards. "By the use of the cam-lever an immense power is obtained, and the juice is extracted from the lemon in a more thorough and perfect manner than when the power is applied directly to the plate or bar carrying the plunger."
This rung works out the cam's average force, with a work check, then builds the frame, the hinged plate and the cam lever in hardwood and steel, and squeezes lemons with it.
Menengah
About 5 hours
Instruksi
1
1
The cam's force
The cam's force
Memuat notebook Jupyter…
2
2
A lever press before it
A lever press before it
The embedded blueprint presses the lemon with the lever itself. Weeks puts a cam lever over a hinged plate, so a turn of the lever gives a far greater push.
3
3
Read US 165,638
Read US 165,638
"Two standards, E E, are attached to the frame A, one on each side, in the upper portions of which standards are bearings for a shaft, f, to which is attached, midway of its length, a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger. J is a spring, which may be of rubber or metal, having its lower end attached to the board or plate C, and its upper end attached to the standard E."
"When the cam-lever G is depressed its face or bearing-surface presses upon the board or plate C, and forces the plunger into the bowl upon the lemon."
4
4
Build the squeezer and press lemons
Build the squeezer and press lemons
**Frame and bowl.** Make a hardwood board frame on four legs, tall enough for a dish beneath, with a hole in it. Fit a tin-can bowl with a punched base into the hole.
**Plate and plunger.** Hinge a hardwood plate to one end of the frame with a butt hinge, and screw a hardwood plunger to its underside so it enters the bowl.
**Standards and cam.** Screw two hardwood standards to the frame's sides beside the plate and run a steel rod across between them as the shaft f. Cut a hardwood cam lever with a curved face whose distance from the shaft grows by about 15 mm over 60° of turn, drill it for the shaft, and fix it in the middle of the rod with a pin.
**Springs.** Hook two extension springs from the plate to the standards so they lift the plate when the cam is raised.
**Test.** Put a half lemon in the bowl over a dish and press the lever down. Compare the juice with a half pressed by pushing the plate down by hand.
Material untuk langkah ini:
Papan Kayu Keras2 buah
Balok Kayu Keras2 buah
Pasak kayu0.6 meter
Sekrup kayu16 buah
Lem Kayu1 buah
Kaleng1 buah
Engsel daun1 buah
Batang Baja Lunak0.2 meter
Paku2 buah
Pegas tarik2 buah
Lemon3 buahAlat yang dibutuhkan:
Gergaji Tangan
Set pahat kayu
Kikir kasar
Bor Tanpa Kabel
Set Mata Bor
Gunting seng
Palu
Set obeng
Gergaji Besi
Pisau dapur
Timbangan Dapur Digital
Sarung Tangan Kerja Kulit5
5
A cam that slips, jams or does not lift
A cam that slips, jams or does not lift
Cam-lever lemon squeezer troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**A. Clarence Weeks** of New York, New York, filed US 165,638 on 26 April 1875; it is dated 13 July 1875. His frame A had feet or legs a, the bowl B had perforations b, the plate C was hinged to one end of the frame, and there could be one spring or two. His claim is the frame with the perforated bowl and standards, the pivoted plate with its plunger, the springs, and the shaft with its cam lever.
**Honest limits.** Hardwood, a tin bowl and a steel rod stand in for his parts. The notebook gives the average force without friction; its forces, lengths and angles are examples. Your juice is the result.
Bahan
11- 2 buahPlaceholder
- 2 buahPlaceholder
- 0.6 meterPlaceholder
- 16 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 0.2 meterPlaceholder
- 2 buahPlaceholder
- 2 buahPlaceholder
- 3 buahPlaceholder
Alat yang Diperlukan
12- Placeholder
- Placeholder
- Placeholder
- 1 vendor sell this, none ship to you yetPlaceholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Blueprint terkait
Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip

The Ring-Set Lemon Squeezer: A Bowl Held in Its Handle by a Screwed Ring
oleh YourGrandma
Pengerjaan Kayu
15
0
0
0
0
0

The False-Bottom Lemon Press: A Hinged Lever Over a Die, and One Hole for the Juice
oleh TheChef
Pengerjaan Kayu
12
0
0
0
0
0

The Clamp-Frame Lemon Squeezer: A Screw Press That Clamps to the Table
oleh Forge
Pengerjaan Logam
8
0
0
0
0
0
CC0 Domain Publik
Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.
Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.