Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)
Forge

Dibuat oleh

Forge

14. November 2026NO
8
0
0
0
0

Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)

The marking scriber Richard Thompson made for his surface gauge in Amateur Work: 1/8 in. steel or a worn-out saw file, drilled in the middle, pointed at both ends with one end bent, annealed by burying it red-hot in lime, filed round while turned in a grooved hardwood block, and the points hardened.
Pemula
Two hours

Instruksi

1

Read Thompson

"A worn-out saw file will answer very well, with a hole drilled through the centre to fit the bolt and pointed at each end, one of which is bent."
2

Rough the shape

Forge a flat piece of steel about 1/8 in. (3 mm) thick, or a worn-out saw file, roughly to shape: pointed at both ends, one end bent into a short hook (his fig. 30).

Material untuk langkah ini:

Batang pipih baja perkakasBatang pipih baja perkakas1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan TempaLandasan Tempa
PaluPalu
Tang pandai besiTang pandai besi
3

Anneal in lime

Heat it gently to a dull red and bury it in lime to cool slowly: it is then easy to file.

Material untuk langkah ini:

Kapur Padam (Kalsium Hidroksida)Kapur Padam (Kalsium Hidroksida)1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Tang pandai besiTang pandai besi
4

Drill and flatten

Drill a hole through the middle to fit the mounting bolt and file the flat part to an even thickness for about 1/2 in. each side of the hole.

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
Ragum MejaRagum Meja
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
5

File it round

Cut a groove along the end of a hardwood block about 3 x 2 x 1/2 in., held end up in the vice. Lay the scriber in the groove, turn it slowly toward you with the left hand and file it round with the right. File the points quite sharp.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Ragum MejaRagum Meja
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
6

Harden the points

Harden the points (he gives no method; ours: heat the tips to a bright red and quench in water), then touch them up on an oilstone.

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Ember pendingin tempaEmber pendingin tempa
Batu asahBatu asah
7

Troubleshooting

Scriber troubleshooting.

Flow

Loading...
8

History and honest limits

From Richard Thompson, "How to Construct a Compound Microscope" III, **Amateur Work, Illustrated**, vol. III, p. 198 and fig. 30 (checked on the archive.org scan amateurworkillus03lond). He mounts the scriber on a mahogany surface gauge with three brass washers 3/4 in. across and 1/16 in. thick. The hardening method, metric figures and tools are ours.

Bahan

3

Alat yang Diperlukan

10

Cetak biru ini membuat

Blueprint terkait

Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...