Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
USB-B Cable: Type-A Plug to Type-B Plug, Wired to the USB 2.0 Specification
Ed

Dibuat oleh

Ed

4. November 2026FI
22
0
0
0
0

USB-B Cable: Type-A Plug to Type-B Plug, Wired to the USB 2.0 Specification

A USB-B cable joins a computer (Type-A plug) to a device such as an Arduino board or a printer (Type-B plug). The USB 2.0 Specification (USB Implementers Forum, 2000) fixes the wiring: contact 1 VBUS on the red wire, 2 D- white, 3 D+ green, 4 GND black, and the plug shells joined through the cable's shield. It also sets the cable's build and its limits: a twisted green-white data pair, a red-black power pair, foil and braid shields, no more than 26 ns of delay, and less than 0.6 ohm from shell to shell. This rung works out how long the cable may be, then cuts a 1.5 m shielded cable, solders a Type-A plug to one end and a Type-B plug to the other, and checks every wire with a multimeter. Source: Universal Serial Bus Specification Rev. 2.0, sections 6.4.1, 6.5.2, 6.6, 7.1.16, 7.2.2. Picture: our own drawing.
Menengah
About 1 hour

Instruksi

1

How long may it be?

The delay and voltage-drop limits from the specification, and what they allow for each wire size.
2

Cut and strip the cable

Cut 1.5 m of shielded USB cable with a 24 AWG power pair. At each end, slit and remove 20 mm of the PVC jacket with the knife. Comb the braid back over the jacket, trim the foil off and keep the bare drain wire. Strip 3 mm of insulation from the red, black, green and white wires.

Material untuk langkah ini:

Kabel USB berpelindungKabel USB berpelindung1.5 m

Alat yang dibutuhkan:

Meteran GulungMeteran Gulung
Pisau katerPisau kater
Tang potong rataTang potong rata
Tang pengupas kabelTang pengupas kabel
Kacamata pengamanKacamata pengaman
3

Solder the Type-A plug

Slide the plug's hood and a 40 mm piece of heat-shrink tubing onto the cable. Tin the wires and solder them to the plug's contacts: 1 red (VBUS), 2 white (D-), 3 green (D+), 4 black (GND). Twist the drain wire into the braid and solder both to the plug's metal shell.

Material untuk langkah ini:

Steker USB tipe ASteker USB tipe A1 buah
Selongsong bakarSelongsong bakar40 mm
Kawat Timah SolderKawat Timah Solder1 as required

Alat yang dibutuhkan:

SolderSolder
Tangan penolongTangan penolong
4

Solder the Type-B plug

Do the same at the other end with the Type-B plug: 1 red (VBUS), 2 white (D-), 3 green (D+), 4 black (GND), drain wire and braid to the shell. Pin 1 must reach pin 1 at both ends.

Material untuk langkah ini:

Steker USB tipe BSteker USB tipe B1 buah
Selongsong bakarSelongsong bakar40 mm
Kawat Timah SolderKawat Timah Solder1 as required

Alat yang dibutuhkan:

SolderSolder
Tangan penolongTangan penolong
5

Check every wire

With the multimeter, check that each contact connects to the same contact at the other end and to no other, and that no contact touches a shell. Measure from shell to shell: the specification asks for less than 0.6 ohm.

Alat yang dibutuhkan:

MultimeterMultimeter
6

Close the plugs

Clip the hoods over the plugs, slide the heat-shrink tubing over each joint between hood and cable, and shrink it with the heat gun as a strain relief.

Alat yang dibutuhkan:

Pistol udara panasPistol udara panas
7

History and honest limits

The specification's revision history dates USB 1.0 to 15 January 1996, 1.1 to 23 September 1998 and 2.0, which added high speed, to 27 April 2000. The specification requires a standard detachable cable to end in OVERMOLDED plugs; ours has hand-soldered plugs in hoods, so it is not a compliant cable. We do not measure its 90 ohm impedance or its delay. The 1.5 m length, the 24 AWG power pair and the strip lengths are ours. How the plugs and the cable are made is not covered (unknown heads).

Bahan

5

Alat yang Diperlukan

9
  • 1 vendor sell this, none ship to you yet
    Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • 2 vendors sell this, none ship to you yet
    Placeholder
  • Placeholder
  • Placeholder
  • 1 vendor sell this, none ship to you yet
    Placeholder

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...