Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Vacuum Gauge: Flattened Curved Tube Driving an Index (Bourdon, US 9,163)
Emma

Dibuat oleh

Emma

9. November 2026SE
3
0
0
0
0

Vacuum Gauge: Flattened Curved Tube Driving an Index (Bourdon, US 9,163)

A vacuum gauge shows how far a line or vessel has been pumped below atmospheric pressure. Eugène Bourdon (US 9,163, 1852) found that a thin metal tube, flattened and bent into a curve, straightens a little under internal pressure and curls up more when the air is drawn out of it. One end is open to the line through a cock; the closed end drives a lever on a spindle that carries the index. With the air withdrawn the index moves the opposite way to a pressure gauge, "and the instrument is then a vacuum gage." Source: E. Bourdon, "Pressure-Gage", US Patent 9,163 (1852). Picture: its Figs. 1-6.
Lanjutan
Unknown

Instruksi

1

Read Bourdon

"If the air be withdrawn from the interior of the tube A by means of an air pump or otherwise the curvature of the tube is increased and the index moves in the opposite direction and the instrument is then a vacuum gage."
2

Make the tube

Flatten a thin metal tube so its section is no longer round (Bourdon draws oval, flat, cross and Y sections) and bend it into a near circle. Close one end (how is not given) and leave the other open. Bourdon: the wall depends on the size, motion, pressure and metal; his only figure is brass about 1/100 in. thick for a barometer about 4 in. across. The metal, wall and size for the vacuum gauge are not given.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 tube

Alat yang dibutuhkan:

Metode pembentukan tak diketahuiMetode pembentukan tak diketahui
Dimensi tidak diketahuiDimensi tidak diketahui
3

Fit the movement

Fix the open end of the tube in the case, connected through a cock to a pipe to the line or vessel. Join the closed end by a link to a short lever on a small spindle that carries the index (or drive the spindle by a toothed sector and pinion, or by a silk thread wound round it and kept tight by a spring). The lever multiplies the tube's movement at the index.

Material untuk langkah ini:

Katup tak diketahuiKatup tak diketahui1 cock
Logam tidak diketahuiLogam tidak diketahui1 link, lever, spindle and index
Logam tidak diketahuiLogam tidak diketahui1 case

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
4

Graduate the dial

Fit a dial behind the index. Bourdon graduates the arc by submitting the instrument to known pressures alongside an ordinary mercury gauge and marking each on the dial; equal steps of pressure give nearly equal degrees. Connect the gauge to a pump drawing the air out: the tube curls more and the index moves the opposite way to a pressure gauge. The reference used to mark a vacuum scale is not given.

Material untuk langkah ini:

Bahan tidak diketahuiBahan tidak diketahui1 dial

Alat yang dibutuhkan:

Pompa vakumPompa vakum

Bahan

3

Alat yang Diperlukan

6

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...