SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Valveless Cone Air Dasher: A Hollow Cone and Four Tubes, Nothing to Wear Out
YourGrandma

Dibuat oleh

YourGrandma

6. Oktober 2026IS
4
0
0
0
0

Valveless Cone Air Dasher: A Hollow Cone and Four Tubes, Nothing to Wear Out

Gridley wanted to force air under the cream "without the employment of valves or other movable parts in the dasher, which are liable to get out of order," and without a hollow handle. Josiah A. Gridley of Southampton, Massachusetts, received US 6,411, dated 1 May 1849, for a churn-dasher of a straight round stick with a hollow cone on its lower end. Near the apex are four holes, more or less, through the cone; from them small tubes run down the outside to near its base, ending in open ends above the base. Forced into the cream, the cone traps air, which is drawn out through the tubes and disperses through the cream. This rung works out the air the cone holds, then prints the cone with its tubes in one piece, fits it to a stick, and makes butter in a jar.
Pemula
About 1 hour, plus printing

Instruksi

1

Air in the cone

Memuat notebook Jupyter…
2

A hollow dash that carries air down before it

The embedded blueprint traps air in a hollow cylinder and squeezes it out over a fixed block. Gridley's cone needs no block, spindle or valve.
3

Read US 6,411

"When this dasher is forced into the cream it incloses and compresses a quantity of air; and as the cream rushes up into it the air is drawn out through the tubes (a partial vacuum being created at their openings above the cone) and disperses through the cream, and agitates it as other air dashers. It is obvious that other figures than a cone would answer, and would be substantially the same thing."
4

Print the cone

Print the cone base-down in one piece (/uploads/blueprints/valveless-cone-air-dasher-cone.stl): a hollow cone 90 mm across with four tubes from holes near its apex down the outside to just above its base, and a socket for the stick. Blow through each tube to check it is clear. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.

Material untuk langkah ini:

Filamen PETGFilamen PETG1 buah

Alat yang dibutuhkan:

Pencetak 3D filamen (FDM)Pencetak 3D filamen (FDM)
5

Fit the stick

Glue a 12 mm hardwood dowel, as long as the jar is deep plus 150 mm, into the cone's socket.

Material untuk langkah ini:

Pasak kayu kerasPasak kayu keras1 buah
Lem KayuLem Kayu1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
AmplasAmplas
6

The churn

Take a tall wide jar about 170 mm across and drill its lid at the centre for the stick.

Material untuk langkah ini:

Stoples KacaStoples Kaca1 buah

Alat yang dibutuhkan:

Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
7

The build in 3D

FreeCAD model of this build, not of the patent: the jar cut away to show the hollow cone on its stick with the four tubes from near its apex to just above its base.
Berkas desainBLENDCC0 - Free
8

Dash and make butter

Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1 litre. Work the stick up and down like a common dasher, lifting the cone clear of the cream each time so it fills with air; watch for bubbles from the tubes. Time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Langkah 8 - Image 1

Material untuk langkah ini:

Krim kentalKrim kental1000 ml
Garam Laut KasarGaram Laut Kasar1 buah
AirAir1 buah

Alat yang dibutuhkan:

Termometer probe tinggal-pasangTermometer probe tinggal-pasang
StopwatchStopwatch
Timbangan Dapur DigitalTimbangan Dapur Digital
Mangkuk aduk baja nirkarat (besar)Mangkuk aduk baja nirkarat (besar)
9

No bubbles, blocked tubes

Valveless cone air dasher troubleshooting.

Flow

Loading...
10

History and honest limits

**Josiah A. Gridley** of Southampton, Hampshire County, Massachusetts, received US 6,411, dated 1 May 1849. His cone was "of metal or other suitable material" and his handle "a straight round stick." He claimed the dasher made concave, with openings around it for dispersing air through the cream, without valves. **Honest limits.** A printed cone stands in for his metal one, and a jar for his churn. The notebook's figures are estimates. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.

Bahan

7
  • Placeholder
  • Placeholder
  • 1 buah
    Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • 1 buah
    Placeholder

Alat yang Diperlukan

9

Berkas desain

1

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...