Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Reversible-Tip Soft-Face Hammer: Domed Rubber Tips Locked in Screw-On Sockets by an Internal Rib (West & Robinson, 1962)
Forge

Dibuat oleh

Forge

13. November 2026NO
11
0
0
0
0

Reversible-Tip Soft-Face Hammer: Domed Rubber Tips Locked in Screw-On Sockets by an Internal Rib (West & Robinson, 1962)

Robert F. West and Walter H. Robinson of Connecticut received US 3,040,792, dated 26 June 1962, for The Stanley Works. A tubular socket screws onto a threaded boss at each end of the hammer's head. A rubber tip, domed at both ends, is pushed into the socket past an internal rib, which bites into it, and its rubber fills short grooves so it cannot turn. The tip can be pulled out and turned round to use its other end. On its first blows the tip's inner face squeezes into an off-centre hole in the boss and forms its own dowel, which stops the socket unscrewing. The patent gives no sizes; every size here is ours.
Lanjutan
About 2 days

Instruksi

1

The tip's proportions

Memuat notebook Jupyter…
2

Read US 3,040,792

"Upon being subjected to the percussive forces during initial use, some of the plastic material of the inner face 27 of the striking tip 26 will be extruded or forced into the eccentrically located recess 12 in the boss surface 10 to provide a self-forming dowel pin 28 which effectively prevents inadvertent loosening of the threaded connection between boss and mounting socket during use."
3

Turn the head 2

From 35 mm steel bar turn a body 4 80 mm long with a boss 8 20 mm across and 15 mm long at each end; cut M20 threads on the bosses with the die. In each boss's end face drill a recess 12 4 mm across and 4 mm deep, 6 mm off centre. Drill a 20 mm handle eye 6 through the middle in a V-block.

Material untuk langkah ini:

Batang bulat baja lunakBatang bulat baja lunak1 buah
Minyak potongMinyak potong1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Cekam bubut 3 rahangCekam bubut 3 rahang
Pahat bubutPahat bubut
Pahat potong bubutPahat potong bubut
Set pembuat ulirSet pembuat ulir
Pemegang sney ulirPemegang sney ulir
Ragum MejaRagum Meja
Mesin Bor DudukMesin Bor Duduk
Blok VBlok V
Set Mata BorSet Mata Bor
PenitikPenitik
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
Kacamata pengamanKacamata pengaman
4

Turn the sockets 14

From 48 mm bar turn two sockets 30 mm long. Knurl the outside 25. Drill and tap the collar end 18 M20, 8 mm deep. From the other end, before boring, drill four 4 mm holes 20 mm deep centred on a 38 mm circle, for the grooves 24. Bore the aperture 16 38 mm across and 20 mm deep, leaving a rib 22 4 mm wide 10 mm in, turned to 35 mm with 30 degree ramps either side.

Material untuk langkah ini:

Batang bulat baja lunakBatang bulat baja lunak2 buah
Minyak potongMinyak potong1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Cekam bubut 3 rahangCekam bubut 3 rahang
Pahat bubutPahat bubut
Batang bor dalamBatang bor dalam
Pahat potong bubutPahat potong bubut
Alat kartelAlat kartel
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Set pembuat ulirSet pembuat ulir
Pemutar tap ulirPemutar tap ulir
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
5

Make the tips 26

For each tip, cut nine discs of 4 mm natural rubber sheet 40 mm across and bond them into a stack with contact cement; clamp it overnight. Grind it round to 38.5 mm on the belt sander, then dome both ends: a large curve over most of the face and a small round where it meets the side, the same at both ends, 36 mm long overall.

Material untuk langkah ini:

Lembaran karet alamLembaran karet alam1 buah
Lem KontakLem Kontak1 buah

Alat yang dibutuhkan:

KompasKompas
Pisau KerajinanPisau Kerajinan
Klem batangKlem batang
Mesin amplas sabukMesin amplas sabuk
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
6

Assemble

Turn an ash handle to drive into the eye and wedge it. Screw a socket onto each boss hand-tight. Push a tip into each socket, squeezing it past the rib in the vice between soft packing, until its inner dome bears on the boss. Give the first few blows on a wood block: the rubber pushes into the boss's recess and locks the socket. To turn a tip round, pull it out, reverse it and push it back.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah
Lem KayuLem Kayu1 buah

Alat yang dibutuhkan:

Mesin bubut kayuMesin bubut kayu
Set pahat bubut (HSS)Set pahat bubut (HSS)
Gergaji BesiGergaji Besi
Palu kepala bulatPalu kepala bulat
Ragum MejaRagum Meja
7

Troubleshooting

Reversible-tip hammer troubleshooting.

Flow

Loading...
8

History and honest limits

**Robert F. West** of Simsbury and **Walter H. Robinson** of West Hartford, Connecticut, assignors to The Stanley Works, US 3,040,792, dated 26 June 1962, filed 31 August 1960. They claimed sockets with an internal portion of reduced cross-section whose surfaces are "inclined to provide ramp surfaces", and symmetrical tips "having end surfaces of convexly curvilinear configuration", removable and "reversible in said sleeves". They list natural rubber, synthetic rubbers, nylon and cellulose esters for the tips; ours are laminated natural rubber. They give proportions but no sizes; every size here is ours.

Bahan

6

Alat yang Diperlukan

24

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...