Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
Woody

Dibuat oleh

Woody

4. November 2026NO
10
0
0
0
0

Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)

A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle. Painted red inside and light green outside, lined in a lighter colour and black. Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
Menengah
Unknown

Instruksi

1

Make the hales

Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.

Material untuk langkah ini:

Papan kayu ashPapan kayu ash1 hales 3 ft 1 in x 1 5/8 x 1 1/2 in

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Ketam tanganKetam tangan
Ketam lengkungKetam lengkung
2

Frame with oak cross-pieces

Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.

Material untuk langkah ini:

Papan ek putihPapan ek putih1 buah
Pasak kayuPasak kayu1 3/16 in pins

Alat yang dibutuhkan:

Gergaji punggungGergaji punggung
Pahat lubang penPahat lubang pen
PerusutPerusut
Bor engkol dan mata borBor engkol dan mata bor
Perusut sudutPerusut sudut
3

Fit the legs and stays

Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.

Material untuk langkah ini:

Papan ek putihPapan ek putih1 legs 1 1/2 in square, stays
Baut kepala bulat leher persegiBaut kepala bulat leher persegi4 3 in

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Bor engkol dan mata borBor engkol dan mata bor
Set obengSet obeng
4

Bottom and sides

Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.

Material untuk langkah ini:

Papan pinusPapan pinus1 1/2 in bottom, 5/8 in sides
Cat minyakCat minyak1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Ketam tanganKetam tangan
Set kuas lukisSet kuas lukis
5

Front board and ironwork

Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.

Material untuk langkah ini:

Papan pinusPapan pinus1 3/4 in front board
Paku BesiPaku Besi1 1 1/2 in cut nails
Besi Strip Baja LunakBesi Strip Baja Lunak1 7/8 in hoop iron
Sekrup kayuSekrup kayu1 3/4 in round-headed
Cat minyakCat minyak1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
PaluPalu
Set obengSet obeng
Set kuas lukisSet kuas lukis
6

Make the wheel

Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.

Material untuk langkah ini:

Papan kayu ashPapan kayu ash1 axle and felloes
Papan ek putihPapan ek putih1 spokes
Batang besi bulatBatang besi bulat1 3/8 in pins
Pasak kayuPasak kayu4 1/4 in
Besi Strip Baja LunakBesi Strip Baja Lunak1 3/4 x 1/8 in tyre

Alat yang dibutuhkan:

Mesin bubut kayuMesin bubut kayu
Ketam lengkungKetam lengkung
Bor engkol dan mata borBor engkol dan mata bor
PaluPalu
7

Hang the wheel and paint

Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.

Material untuk langkah ini:

Besi Strip Baja LunakBesi Strip Baja Lunak2 3/4 x 1/8 in irons
Sekrup kayuSekrup kayu1 buah
Cat minyakCat minyak1 buah

Alat yang dibutuhkan:

Set obengSet obeng
Set kuas lukisSet kuas lukis

Bahan

10

Alat yang Diperlukan

12

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...