कला
सौंदर्य और कल्याण
हस्तशिल्प
संस्कृति और इतिहास
मनोरंजन
पर्यावरण
खाद्य और पेय
हरित भविष्य
रिवर्स इंजीनियरिंग
विज्ञान
खेल
प्रौद्योगिकी
पहनने योग्य
Building a Thatched Lean-To Shelter — Basic Wind and Rain Protection
The lean-to is one of the most basic and universal shelter forms — a single sloped roof supported by a ridge pole between two trees or upright posts, with the low side facing away from the prevailing wind. The design sheds rain, blocks wind from one direction, and reflects the heat of a fire built in front of the open side back toward the sleeping area. Thatching the roof with overlapping layers of grass, ferns, bark, or leaves (working from bottom to top like roof tiles) creates a waterproof layer that keeps the interior dry. A lean-to can be built in 2-3 hours from materials found in any woodland or grassland, making it the default emergency shelter worldwide.
शुरुआती
2-3 hours
निर्देश
1
1
Select Support Trees or Stakes
Select Support Trees or Stakes
Select two trees or drive two forked stakes into the ground 2-3 metres apart.
2
2
Place the Ridge Pole
Place the Ridge Pole
Place a ridge pole (straight, strong branch 3-4m long) in the forks at about chest height (1.2-1.5m).
इस चरण के लिए सामग्री:
Hardwood Sapling3 टुकड़े3
3
Orient Against the Wind
Orient Against the Wind
The ridge pole should run perpendicular to the prevailing wind direction.
4
4
Lean Rafters Against the Ridge Pole
Lean Rafters Against the Ridge Pole
Lean rafters (straight branches 2-3m long) against the ridge pole at 45-60 degrees, spaced 20-30cm apart.
5
5
Secure the Rafters
Secure the Rafters
Lash the rafters to the ridge pole with cordage, or let gravity hold them.
इस चरण के लिए सामग्री:
Cordage2 टुकड़े6
6
Weave the Lattice
Weave the Lattice
Weave thin, flexible branches horizontally through the rafters at 15-20cm intervals to create a lattice.
7
7
Begin Thatching from the Bottom
Begin Thatching from the Bottom
Starting at the bottom, lay thick bundles of grass, fern fronds, or large leaves on the lattice.
8
8
Overlap Each Layer
Overlap Each Layer
Each layer should overlap the one below by at least half — this shingles the water downward.
9
9
Complete the Thatch to the Ridge
Complete the Thatch to the Ridge
Continue layering to the ridge pole — the thatch should be 10-15cm thick for rain protection.
10
10
Build a Reflector Fire
Build a Reflector Fire
Build a long fire parallel to the open side, 1 metre from the sleeping area.
11
11
Insulate the Sleeping Area
Insulate the Sleeping Area
Line the sleeping area with dry leaves, grass, or a rush mat for insulation from the cold ground.
कनेक्टेड ब्लूप्रिंट सामग्री
संबंधित ब्लूप्रिंट
ये ब्लूप्रिंट ज्ञान साझा करते हैं — तकनीक, सामग्री या सिद्धांत
CC0 पब्लिक डोमेन
यह ब्लूप्रिंट CC0 के तहत जारी किया गया है। आप बिना अनुमति माँगे इस कार्य को किसी भी उद्देश्य के लिए कॉपी, संशोधित, वितरित और उपयोग करने के लिए स्वतंत्र हैं।
उनके ब्लूप्रिंट के माध्यम से उत्पाद खरीदकर मेकर का समर्थन करें जहाँ वे मेकर कमीशन कमाते हैं जो विक्रेताओं द्वारा निर्धारित होता है, या इस ब्लूप्रिंट का नया संस्करण बनाएँ और राजस्व साझा करने के लिए इसे अपने ब्लूप्रिंट में कनेक्शन के रूप में शामिल करें।