همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
5mm LED: Epoxy Lamp with a Reflector-Cup Lead Frame (Kosman, US 3,821,590, 1974)
Ed

ایجاد شده توسط

Ed

3. نوامبر 2026FI
۸
۰
۰
۰
۰

5mm LED: Epoxy Lamp with a Reflector-Cup Lead Frame (Kosman, US 3,821,590, 1974)

A round LED indicator lamp about 0.200 in (5 mm) across. A red GaP chip sits on a small pedestal at the focus of a paraboloid reflector cup that is part of the lead frame. A fine wire runs from the chip to the other lead. The whole is moulded in clear or tinted epoxy, with small lenses moulded into the front face to spread the light. Result: an encapsulated LED lamp visible within about ±45°, moulded many at a time on one lead frame. Source: K. J. W. Kosman and L.-P. Boivin (Northern Electric), US 3,821,590 (1974). Unknown: lead and wire metals, die attach and cure. Picture: the patent drawing.
متخصص
Unknown

دستورالعمل‌ها

1

Make the lead frame with its reflector

Make a lead frame carrying many lamps. In each, the negative lead ends in a paraboloid reflector cup with a small pedestal at its focus, and the positive lead ends nearby. Not given: the metal, sizes beyond the lamp's 0.200 in diameter.

مواد مورد نیاز این مرحله:

فلز نامعلومفلز نامعلوم1 lead frame

ابزارهای مورد نیاز:

ابعاد نامعلومابعاد نامعلوم
2

Mount and bond the chip

Mount a light-emitting chip with a P-N junction, for example red GaP:Zn,O, on the pedestal, so the cup makes contact with one side of the junction. Connect the other side by a fine wire to the positive lead. About 0.015 in square is the junction size Kosman gives for best efficiency. Not given: the die attach, the wire metal.

مواد مورد نیاز این مرحله:

تراشه LEDتراشه LED1 light-emitting chip
فلز نامعلومفلز نامعلوم1 bond wire

ابزارهای مورد نیاز:

ابعاد نامعلومابعاد نامعلوم
3

Transfer-mould the lamps

Set the bonded lead frame in a mould and transfer-mould clear or tinted thermosetting resin round all the lamps at once, front face down so any flaws fall at the back. The front face carries seven spherical lenses, six in a ring round one, each 0.045 in across with a radius about 0.8 times its width; an inclined edge sends some light out sideways. Ours: bisphenol epoxy (the patent lists epoxy, silicone, polyester or diallyl phthalate). Not given: the mould, the cure.

مواد مورد نیاز این مرحله:

رزین اپوکسی بیس‌فنولرزین اپوکسی بیس‌فنول1 capsule resin

ابزارهای مورد نیاز:

پرس انتقالی رزینپرس انتقالی رزین
روش شکل‌دهی ناشناختهروش شکل‌دهی ناشناخته
4

Cut apart and test

Cut the lamps from the lead frame and light each one with current forward through the junction: the face shows seven bright spots in a 0.100 in image, visible up to about 45° off axis. Not given: the current.

ابزارهای مورد نیاز:

منبع تغذیهٔ جریان مستقیممنبع تغذیهٔ جریان مستقیم

مواد

3

ابزارهای لازم

4

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...