همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)
Woody

ایجاد شده توسط

Woody

4. نوامبر 2026NO
۱۱
۰
۰
۰
۰

Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)

A shop belt sander for dressing wood surfaces: a 6 in garnet-paper belt running over four crowned wooden pulleys, one driven by the lathe, pressed down onto the work with a hand float. Best belt speed about 2,500 ft per minute; leave about 1 in between work and belt. Source: Popular Mechanics Shop Notes for 1919, p. 3235. Picture: the article's drawing.
متوسط
Unknown

دستورالعمل‌ها

1

Turn the pulleys

Build up four solid wood pulleys 10 in across with 8 in faces and turn them in the lathe with a very slight crown; too much crown harms the belt.

مواد مورد نیاز این مرحله:

تختهٔ چوب سختتختهٔ چوب سخت4 built-up pulleys

ابزارهای مورد نیاز:

تراش چوبتراش چوب
2

Mount the pulleys

Mount one pulley on a firmly held arbor in the lathe and the other three on iron-pipe shafts on a frame (drawing). Turn and file a true journal on each pipe, pour babbitt bushings in the pulleys, and cut oil grooves in the pipe or babbitt. Supporting the shafts on one side lets the belt slip off; supporting both sides is stronger.

مواد مورد نیاز این مرحله:

لوله فولادی (جدارضخیم، با سرهای رزوه‌دار)لوله فولادی (جدارضخیم، با سرهای رزوه‌دار)3 shafts
فلز نامعلومفلز نامعلوم1 babbitt bushings
الوار کاجالوار کاج1 frame

ابزارهای مورد نیاز:

سوهان فلزسوهان فلز
کفگیر سوراخ‌دارکفگیر سوراخ‌دار
ارهٔ دستیارهٔ دستی
چکشچکش
3

Make the belt

Cut 6 in garnet paper (No. 1 1/2 for general work) so the ends just meet over the pulleys. Glue the smooth side at the joint, splice it with a strip of cloth about 1 in wide and then one about 3 in wide, cover each side with paper, and clamp between two small boards.

مواد مورد نیاز این مرحله:

کاغذ سنبادهکاغذ سنباده1 6 in garnet paper
پارچهٔ پنبه‌ایپارچهٔ پنبه‌ای1 قطعه
سریشم حیوانیسریشم حیوانی1 قطعه

ابزارهای مورد نیاز:

گیرهٔ سی‌شکلگیرهٔ سی‌شکل
4

Set up and run

Run the belt at about 2,500 ft per minute using the lathe's cone pulley. Set the work about 1 in below the belt on a table or a low sliding platform (two sets of tongue-and-groove joints at right angles), start the machine and press the belt down with a float like a blackboard eraser, or a roller.

مواد مورد نیاز این مرحله:

الوار کاجالوار کاج1 platform, float

ابزارهای مورد نیاز:

تراش چوبتراش چوب

مواد

7

ابزارهای لازم

6

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...