همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Bench Power Supply: Regulated, with Adjustable Current Limit and a Pentode Pass Tube (Gately, Forbro, US 3,243,690, 1966)
Ed

ایجاد شده توسط

Ed

3. نوامبر 2026FI
۱۲
۰
۰
۰
۰

Bench Power Supply: Regulated, with Adjustable Current Limit and a Pentode Pass Tube (Gately, Forbro, US 3,243,690, 1966)

An adjustable bench supply that holds its output voltage steady and lets you set the most current it will deliver, so a circuit under test cannot be damaged. A pentode tube in series with the output is the regulator; a bridge with Zener references and a five-transistor amplifier keeps the output equal to the setting of one knob. A meter switch reads volts, amps, and the current limit, which can be set without disturbing the voltage. Result: a regulated DC bench supply with adjustable current limiting. Source: J. R. Gately (Forbro Design), US 3,243,690 (1966). Unknown: all component values and the output rating. Picture: the patent drawing.
پیشرفته
Unknown

دستورالعمل‌ها

1

Wire the mains side

In a case, wire the power cord through a switch and a fuse to the primary of a transformer with four secondaries, and put a neon lamp across the primary to show the supply is on. One secondary (6.3 V) goes to two terminals for outside use, one heats the pentode, one is the main supply and one the bias supply. Ours: the case. Not given: the other winding voltages.

مواد مورد نیاز این مرحله:

جعبهٔ آلومینیومیجعبهٔ آلومینیومی1 case
سیم انعطاف‌پذیر با دوشاخهسیم انعطاف‌پذیر با دوشاخه1 قطعه
کلید اهرمیکلید اهرمی1 قطعه
فیوزفیوز1 قطعه
ترانسفورماتور کاهندهترانسفورماتور کاهنده1 four secondaries
لامپ نشانگر نئونلامپ نشانگر نئون1 قطعه
پست اتصالپست اتصال2 6.3 V terminals

ابزارهای مورد نیاز:

دریل دستیدریل دستی
مجموعه پیچ‌گوشتیمجموعه پیچ‌گوشتی
2

Build the rectifiers

Rectify the centre-tapped main winding with two rectifiers and smooth it with a capacitor. From the bias winding make two more supplies: one through two rectifiers with by-pass capacitors to a smoothing capacitor, for the pentode's screen and the reference circuit; the other through one rectifier and a capacitor, for the pentode's grid bias. Not given: the values.

مواد مورد نیاز این مرحله:

دیوددیود5 rectifiers
خازن الکترولیتیخازن الکترولیتی3 smoothing
کیت خازنکیت خازن1 by-pass
سیم لحیمسیم لحیم1 as needed

ابزارهای مورد نیاز:

هویههویه
3

Fit the pass tube and reference

Put the pentode in series with the positive output: plate to the main supply, cathode through two current-sensing resistors (one fixed, one adjustable) to the + output terminal; suppressor tied to the cathode, screen fed through a resistor. Build the reference: a Zener fed through a resistor feeds a second Zener at constant current, giving a fixed voltage. Against it set two resistors and the voltage-control variable resistor: the output voltage is proportional to that resistor's setting. Not given: the tube type and values.

مواد مورد نیاز این مرحله:

لامپ پنتودلامپ پنتود1 series pass tube
دیود زنردیود زنر2 قطعه
مقاومتمقاومت1 مجموعه
رئوستارئوستا2 voltage control, current-limit range
پست اتصالپست اتصال2 output + and -
سیم لحیمسیم لحیم1 as needed

ابزارهای مورد نیاز:

هویههویه
4

Build the error amplifier and current limit

Build a five-transistor amplifier that drives the pentode's grid to keep the bridge balanced: a PNP emitter follower, an NPN stage, a PNP emitter follower with a resistor-capacitor roll-off against oscillation, a PNP driver whose base resistor has a capacitor across it for quick response, and an NPN clamp whose base is set by a potentiometer. Feed the voltage across the current-sensing resistors to the driver's base through a diode: above the limit it takes over and turns the pentode down. Choose the fixed sensing resistor to limit at about 125 % of rated current, trim with the potentiometer, and use the adjustable one to set lower limits. Not given: the transistor types and values.

مواد مورد نیاز این مرحله:

ترانزیستور PNPترانزیستور PNP3 قطعه
ترانزیستور NPNترانزیستور NPN2 قطعه
دیوددیود1 قطعه
پتانسیومترپتانسیومتر1 قطعه
کیت خازنکیت خازن1 roll-off, speed-up
مقاومتمقاومت1 مجموعه
سیم لحیمسیم لحیم1 as needed

ابزارهای مورد نیاز:

هویههویه
5

Fit the meter and use it

Fit a meter with a four-pole, three-position switch. Position 1 reads output volts through a multiplier resistor; position 2 reads current across a shunt in the negative line; position 3 (spring-return) puts a load resistor across the output and swaps a fixed resistor for the voltage control, so you can turn the limit control until the current limits at the value you want, without touching the voltage setting. Release the switch and use the supply.

مواد مورد نیاز این مرحله:

نمایشگر عقربه‌ای پنلی با پیچهٔ متحرکنمایشگر عقربه‌ای پنلی با پیچهٔ متحرک1 قطعه
کلید چرخانکلید چرخان1 4-pole, 3-position
مقاومتمقاومت1 multiplier, shunt, load resistors
ماده ناشناختهماده ناشناخته1 terminal strip

ابزارهای مورد نیاز:

هویههویه
مجموعه پیچ‌گوشتیمجموعه پیچ‌گوشتی

مواد

21

ابزارهای لازم

3

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...