همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Jointed Fishing Rods: Two- and Three-Piece Casting, Trout and Bass Fly, Salt-Water and Tarpon Rods (Boy Mechanic, 1915)
Woody

ایجاد شده توسط

Woody

13. نوامبر 2026NO
۷
۰
۰
۰
۰

Jointed Fishing Rods: Two- and Three-Piece Casting, Trout and Bass Fly, Salt-Water and Tarpon Rods (Boy Mechanic, 1915)

Part II of Stillman Taylor's rod-making series (The Boy Mechanic, Book 2, 1915): once the one-piece casting rod is mastered, the same planing, grasp and finishing methods make jointed rods. He gives full caliper tables and fitting lists for six rods; choose one in the notebook. Sections join with welted, shouldered ferrules, and every rod gets two tips "in view of a possible breakage".
پیشرفته
About 2-3 weeks (glue and varnish drying)

دستورالعمل‌ها

1

His caliper tables

در حال بارگذاری دفترچهٔ Jupyter…
2

Read The Boy Mechanic, Book 2

"While the action of the one-piece rod is undeniably better than when the rod is made in two or three pieces, it is less compact to carry." He warns that "the more joints incorporated in a rod, the less satisfactory it will be from an angling standpoint", since ferrules cannot follow the rod's curve.
3

Choose the rod and get the stock

Pick a rod from the notebook. Stock (dagame or greenheart): two-piece casting -- butt 5/8 in x 3 ft, two tips 3/8 in x 3 ft; three-piece casting -- all 2 ft, butt 5/8 in, joint and tips 3/8 in; trout or bass fly -- butt 5/8 in x 4 ft, joint and tips 3/8 in x 4 ft; salt-water -- both 4 ft, butt 3/4 in, tip 1/2 in; tarpon -- one piece 1 in x 6-1/2 ft.

مواد مورد نیاز این مرحله:

چوب داگامهچوب داگامه4 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
متر نواریمتر نواری
4

Plane each section to its table

Plane, round and scrape each section exactly as for the one-piece rod, calipering at every station in the table. Two-piece casting rod: he first suggests a butt of about 23 in and a 32-1/2 in tip to fit a 35 in rod case, then specifies a 6-1/2 oz rod with a 32-1/2 in butt (15/32 in at the grasp to 19/64 in at the ferrule) and a 33 in tip (17/64 in to 7/64 in), equal when ferrule and top are on. Make two tips for each rod.

مواد مورد نیاز این مرحله:

کاغذ سنبادهکاغذ سنباده1 قطعه

ابزارهای مورد نیاز:

رندهٔ دستیرندهٔ دستی
رندهٔ کفیرندهٔ کفی
کاردک فولادیکاردک فولادی
سوهان (سوهان دستی)سوهان (سوهان دستی)
کولیس ورنیهکولیس ورنیه
5

Fit the ferrules

Fit a welted, shouldered ferrule at each joint, sized from his list: 17/64 in for the two-piece casting rod; 21/64 in and 15/64 in for the three-piece; 9/32 in and 11/64 in for the fly rods; 7/16 in for the salt-water rod; a 3/4 in male ferrule on the tarpon butt. The tip ferrule comes with two closed-end centres, one for each tip. Cement them on with ferrule cement; serrated (toothed) ferrule ends are wound with silk for strength.

مواد مورد نیاز این مرحله:

بوشن اتصال چوب‌ماهیگیریبوشن اتصال چوب‌ماهیگیری2 قطعه
چسب بوشنچسب بوشن1 قطعه
ابریشم پیچیدن چوب‌ماهیگیریابریشم پیچیدن چوب‌ماهیگیری1 قطعه

ابزارهای مورد نیاز:

سوهان (سوهان دستی)سوهان (سوهان دستی)
مشعل پروپانمشعل پروپان
کولیس ورنیهکولیس ورنیه
6

Build the grasp and reel seat

Build the cork grasp and reel seat as for the one-piece rod: 3/4 in reel seat with straight hood for the casting rods (fly-rod type with butt cap on the fly rods, 9 in or 9-1/2 in of cork above it), 7/8 in on the salt-water rod with an 18 in double grasp, 1 in on the tarpon rod. Use a 1 in butt cap (1-1/8 in on the tarpon rod) and a taper (winding check) of the small-end size in his list. For an independent butt, fit the ferrule straight on a rounded dagame core so the seated ferrule does not touch the wood, cement and rivet it, fit a soft-pine sleeve over core and ferrule, glue it on, cement and rivet the reel seat, then glue on the corks and cut the core flush.

مواد مورد نیاز این مرحله:

حلقه‌های چوب‌پنبهحلقه‌های چوب‌پنبه24 قطعه
سریشم حیوانیسریشم حیوانی1 قطعه
تختهٔ کاجتختهٔ کاج1 قطعه
جای قرقرهجای قرقره1 قطعه
درپوش تهٔ چوب‌ماهیگیریدرپوش تهٔ چوب‌ماهیگیری1 قطعه
حلقهٔ پایانی دستهحلقهٔ پایانی دسته1 قطعه
چسب بوشنچسب بوشن1 قطعه
پرچ مسیپرچ مسی1 قطعه

ابزارهای مورد نیاز:

چاقوی کاردستیچاقوی کاردستی
دریل دستیدریل دستی
رندهٔ کفیرندهٔ کفی
مشعل پروپانمشعل پروپان
چکشچکش
7

Mount the guides and tops

Casting rods: two 1/2 in narrow agate guides, two No. 1 one-ring casting guides and two 3/32 in offset agate tops. Fly rods: two No. 4 snake guides on the butt joint, three No. 3 on the middle joint, three No. 2 on each tip, and two No. 7 agate angle fly tops of the wind-on kind. Salt-water rod: a 10/32 in stirrup-tube agate top and two No. 3 bell guides. Tarpon rod: two No. 11 wide raised agate guides, two No. 1 trumpet guides and a 3/8 in agate stirrup top; whip its guides on double, the first set 10 in from the top, the second 26 in from the reel. Whip with 00 silk (00 or 0 on the three-piece rod, size A on the salt-water and tarpon rods), using the invisible knot.

مواد مورد نیاز این مرحله:

حلقهٔ راهنمای نخحلقهٔ راهنمای نخ8 قطعه
حلقهٔ سرِ چوبحلقهٔ سرِ چوب2 قطعه
ابریشم پیچیدن چوب‌ماهیگیریابریشم پیچیدن چوب‌ماهیگیری1 قطعه
موم زنبور عسلموم زنبور عسل1 قطعه

ابزارهای مورد نیاز:

سوهان (سوهان دستی)سوهان (سوهان دستی)
چاقوی کاردستیچاقوی کاردستی
8

Shellac and varnish

Shellac the windings and varnish the rod with coach varnish as for the one-piece rod: thin coats, warm, three days between coats.

مواد مورد نیاز این مرحله:

ورنی شلاکیورنی شلاکی1 قطعه
ورنی کالسکهورنی کالسکه3 قطعه

ابزارهای مورد نیاز:

قلم‌موی پهنقلم‌موی پهن
9

Troubleshooting

Jointed rod troubleshooting.

Flow

Loading...
10

History and honest limits

From "Fishing-Rod Making and Angling, Part II" by Stillman Taylor, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 69-72). Two points are given as he wrote them: the two-piece casting rod's butt is about 23 in in one sentence and 32-1/2 in in the next; the three-piece rod's stock is "2 ft. long" while its finished sections are 21-1/2, 21-3/4 and 21 in. Guide counts in the list are for the fly rods, the largest set. The tools and metric figures are ours.

مواد

17

ابزارهای لازم

12

این نقشه می‌سازد

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...