هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Carbon Resistance Strip: Carbon and Phenolic Resin in Acetone, Cured on Semi-Cured Phenolic Sheet
Ed

ایجاد شده توسط

Ed

21. اکتبر 2026FI
۱۴
۰
۰
۰
۰

Carbon Resistance Strip: Carbon and Phenolic Resin in Acetone, Cured on Semi-Cured Phenolic Sheet

Podolsky (Wirt Company, US 2,060,114, 1936) bonded the carbon film into its base: the phenolic sheet is only half cured, the coating carries the same kind of resin, and its solvent (acetone) softens the sheet's surface. Heated calender rolls then finish the cure of sheet and coating together, so the track is hard, does not rub off and lasts. Cut across, the sheet gives resistance strips for a variable resistor. The picture: our diagram.
متوسط
1 day

دستورالعمل‌ها

1

Mix 21 carbon, 26 resin, 53 solvent

Make a solution of 21 % carbon, 26 % phenol-formaldehyde resin and 53 % acetone. The patent says the exact proportions are not essential; this is its example.

مواد مورد نیاز این مرحله:

کربنکربن21 parts
باکلیت مایع (فراورده تراکمی فنل-فرمالدهید)باکلیت مایع (فراورده تراکمی فنل-فرمالدهید)26 parts

ابزارهای مورد نیاز:

استوناستون
ترازوی دو کفهترازوی دو کفه
بشر شیشه‌ایبشر شیشه‌ای
هم‌زنهم‌زن
ماسک تمام‌صورتماسک تمام‌صورت
دستکش لاستیکیدستکش لاستیکی
2

Coat the semi-cured sheet

Use a phenolic sheet whose cure was stopped before it fully hardened. A roller turning in a pan of the solution coats its underside.

مواد مورد نیاز این مرحله:

ورق فنولیک نیمه‌پختهورق فنولیک نیمه‌پخته1 قطعه

ابزارهای مورد نیاز:

جفت غلتک پوشش‌دهی غوطه‌وریجفت غلتک پوشش‌دهی غوطه‌وری
ماسک تمام‌صورتماسک تمام‌صورت
دستکش لاستیکیدستکش لاستیکی
3

Cure between calender rolls at 350 °F

Pass the coated sheet between calender rolls heated to about 350 °F (177 °C). This finishes the cure and bonds the coating to the sheet. The patent sometimes calenders it again to burnish the surface.

ابزارهای مورد نیاز:

غلتک‌های کالندر گرمغلتک‌های کالندر گرم
دستکش گرمااستواردستکش گرمااستوار
4

Cut into strips

Cut the sheet across into strips of the width wanted. Ours: tin snips.

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
دستکش لاستیکیدستکش لاستیکی

مواد

3

ابزارهای لازم

10

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...