همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Card Clothing: Twin-Toothed Wire Staples Set in Shaved Leather (Ure, 1839)
Tex

ایجاد شده توسط

Tex

5. نوامبر 2026FO
۱۲
۰
۰
۰
۰

Card Clothing: Twin-Toothed Wire Staples Set in Shaved Leather (Ure, 1839)

Card clothing is the toothed face of a card: leather set with rows of bent wire staples. Andrew Ure's Dictionary of Arts (1839) explains why it is hard to make well. Every staple gives two teeth, and both teeth must be bent to exactly the same angle; the twin holes for each staple must slope at the same angle through the leather; and the leather must be the same thickness everywhere, or the teeth stand at different lengths and the card works unevenly. Factories shaved the leather to an even thickness, losing about half its weight, and gave the wire and leather out to be put together by hand. Ure gives no wire metal, gauge, tooth length, angle or hole spacing; those are unknown here. Source: Andrew Ure, A Dictionary of Arts, Manufactures and Mines (1839), CARDS. Picture: his figs. 267-269, card teeth and one staple.
متوسط
A day for a small sheet

دستورالعمل‌ها

1

Read Ure

"Cards are formed of a sheet or fillet of leather pierced with a multitude of small holes, in which are implanted small staples of wire with bent projecting ends called teeth. Thus every piece of wire is double toothed."
2

Shave the leather even

Shave the leather to the same thickness over its whole surface; in the factory about half its weight is lost in shaving and trimming. If the thickness varies, teeth of the same length stand at different heights. The thickness is not given (unknown).

مواد مورد نیاز این مرحله:

چرم دبّاغی گیاهیچرم دبّاغی گیاهی1 ورق

ابزارهای مورد نیاز:

چاقوی نازک‌کاری چرمچاقوی نازک‌کاری چرم
ابعاد نامعلومابعاد نامعلوم
3

Bend the staples

Cut the wire into equal lengths. Bend each length at right angles at two points (c and d in fig. 268) to make a staple, then bend each leg again at the same obtuse angle (a and b), so the two teeth lean the same way. Every staple must be bent alike. The metal and gauge of the wire, the tooth length and the angle are not given (unknown).

مواد مورد نیاز این مرحله:

فلز نامعلومفلز نامعلوم1 wire

ابزارهای مورد نیاز:

سیم‌چینسیم‌چین
انبردست تختانبردست تخت
ابعاد نامعلومابعاد نامعلوم
4

Prick the twin holes

Prick the leather with pairs of holes the width of a staple apart (c to d), in regular rows, every hole sloping at the same angle through the leather. The spacing is not given (unknown).

ابزارهای مورد نیاز:

درفشدرفش
ابعاد نامعلومابعاد نامعلوم
5

Set the staples

Push each staple through its two holes from the back, so the cross piece (c d) lies against the back of the leather and holds it, and the teeth stand out on the face all leaning one way.

ابزارهای مورد نیاز:

انبردست تختانبردست تخت
6

History and honest limits

By 1839 machines at Halifax, Leeds, Glasgow and Lille shaved the leather, pierced it, cut and bent the wire and set the staples; Ure describes a machine that does all four in turn. Card clothing was then nailed to the flat or cylindrical wooden or metal surfaces of hand cards and carding engines. The wire metal and gauge, tooth length, knee angle, hole spacing and leather thickness are not given; vegetable-tanned leather stands for the card leather.

مواد

2

ابزارهای لازم

5

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...