همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Screw-Depth Portable Router: The Motor's Threaded Casing Screws Into a Split Base, One Turn per Sixteenth (Carter, 1924)
Forge

ایجاد شده توسط

Forge

13. نوامبر 2026NO
۹
۰
۰
۰
۰

Screw-Depth Portable Router: The Motor's Threaded Casing Screws Into a Split Base, One Turn per Sixteenth (Carter, 1924)

Ray L. Carter of Syracuse, New York, received US 1,514,894, dated 11 November 1924, for the portable electric router: a small high-speed motor in an insulated casing light enough to hold in one hand, with a cutter in a chuck on its shaft. The casing is threaded outside and screws into the split, threaded top of a hollow base with a flat bottom. Each turn moves the cutter 1/16 inch, and a clamp screw across the split locks it. The base is cut away so the cutter can be seen and the chips can get out. We print the casing and base in PETG at his pitch, round a small DC motor. The other sizes are ours.
متوسط
About 2 days

دستورالعمل‌ها

1

One turn, one sixteenth

در حال بارگذاری دفترچهٔ Jupyter…
2

Read US 1,514,894

"In practice, the threads of the shell 3 and support 9 are preferably about one-sixteenth inch pitch, so that each revolution of the motor or support in either direction moves the tool A correspondingly."
3

Print the motor casing

The casing 3: a tube for a 42 mm motor with a 60 mm thread at 1/16 inch pitch, an 18 mm hole and air slots in its bottom, and two holes 29 mm apart for the motor's face screws. Print it bottom down. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
فایل طراحیSTLCC0 - Free
4

Print the base

The support 9: a hollow base with a flat plate 140 mm across and an opening 50 mm wide, its sides cut away, two wings, and the split, threaded top with clamp lugs. Print it plate down. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
فایل طراحیSTLCC0 - Free
5

Print and fit the parts

Print the casing and the base in PETG. Clean the threads and screw the casing into the base by hand; it should turn smoothly all the way. If it is tight, run it in and out a few times. Check the base's bottom is flat by rubbing it on abrasive paper on a flat board.

مواد مورد نیاز این مرحله:

فیلامنت PETGفیلامنت PETG1 قطعه

ابزارهای مورد نیاز:

چاپگر سه‌بعدی رشته‌ای (FDM)چاپگر سه‌بعدی رشته‌ای (FDM)
ابزار پلیسه‌گیریابزار پلیسه‌گیری
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
6

Motor, collet and wiring

Fit the collet adapter on the motor's shaft and tighten its set screws. Push the motor down into the casing so its face sits on the casing's bottom with the collet through the hole, and screw it in with its two M4 face screws. Solder the supply leads through a toggle switch, sleeve the joints, and lead the cable out through the casing's open top. Set the DC supply to the motor's rated voltage.

مواد مورد نیاز این مرحله:

موتور برقیموتور برقی1 قطعه
آداپتور کولت شفت موتورآداپتور کولت شفت موتور1 قطعه
پیچ آلن سرتخت‌استوانه‌ایپیچ آلن سرتخت‌استوانه‌ای2 قطعه
کلید اهرمیکلید اهرمی1 قطعه
سیم اتصالسیم اتصال1 قطعه
لولهٔ حرارتی جمع‌شوندهلولهٔ حرارتی جمع‌شونده1 قطعه

ابزارهای مورد نیاز:

منبع تغذیهٔ جریان مستقیممنبع تغذیهٔ جریان مستقیم
هویه برقیهویه برقی
مجموعه آچار آلنمجموعه آچار آلن
آچار فرانسهآچار فرانسه
7

Set the depth and lock it

Fit a straight bit in the collet. Screw the casing into the base until the bit's end is level with the base's bottom on a flat board, then screw it in four more turns for a 1/4 inch (6.35 mm) deep cut. Put an M5 screw through the lugs with a wing nut and tighten it, closing the split on the thread.

مواد مورد نیاز این مرحله:

پیچ آلن سرتخت‌استوانه‌ایپیچ آلن سرتخت‌استوانه‌ای1 قطعه
مهره بالدارمهره بالدار1 قطعه

ابزارهای مورد نیاز:

مجموعهٔ تیغه‌های اورفرزمجموعهٔ تیغه‌های اورفرز
مجموعه آچار آلنمجموعه آچار آلن
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
8

Rout a groove

Clamp a board down. Hold the router by its casing and wings, base flat on the board, switch on, and move it along a clamped straightedge so the bit cuts a groove. Take deep grooves in two or three passes, a few turns deeper each time.

ابزارهای مورد نیاز:

تختهٔ چوب سختتختهٔ چوب سخت
گیرهٔ میله‌ایگیرهٔ میله‌ای
عینک ایمنیعینک ایمنی
9

Troubleshooting

Router troubleshooting.

Flow

Loading...
10

History and honest limits

**Ray L. Carter** of Syracuse, New York, US 1,514,894, dated 11 November 1924, filed 29 September 1923. He claimed a motor with a threaded casing, "a hollow cylinder having a split threaded portion adapted to engage the threaded portion of said casing whereby said tool may be moved relatively to the work", a plane bottom to move over the work, and means for locking. His motor ran on mains through a lamp socket at over 7,000 r.p.m.; ours is a small DC motor on a bench supply, a light-duty router. His casing was insulating material; ours is printed PETG. His fan and baffle disk are left out. The pitch is his; the other sizes are ours.

مواد

8

ابزارهای لازم

11

فایل‌های طراحی

2

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...