همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Chemical Splash Goggles: One Sealed Lens in a Moulded Rubber Frame (Hirschmann, 1954)
Emma

ایجاد شده توسط

Emma

2. نوامبر 2026SE
۱۶
۰
۰
۱
۰

Chemical Splash Goggles: One Sealed Lens in a Moulded Rubber Frame (Hirschmann, 1954)

Goggles for work with corrosive liquids. One clear plastic lens covers both eyes and sits sealed all round in a soft moulded rubber frame that seals against the face. The version for gas and corrosive liquids has no vent holes at all, and the strap passes through tabs outside the lens, so nothing can leak through or around the part you look through. Result: chemical splash goggles with a lens you can pull out and replace, and a strap pull shared evenly between lens and frame, so neither warps. Source: J. B. Hirschmann, US Patent 2,680,846 (1954), Fig. 4 version. Unknown: sizes, the rubber compound, the strap material and how the frame is moulded. Ours: the mould; the patent tested a cellulose acetate lens. Picture: patent drawing.
متوسط
2 days

دستورالعمل‌ها

1

Mould the rubber frame

Mould the frame in one piece from rubber. The front rim has one opening shaped for both eyes, narrower above the nose. Behind it, a wall forms the eye chamber and ends in a double flange that seals against the face. Inside the rim, form a channel between an outer and an inner flange to hold the lens edge. At each end, mould a lug with a strap slot and a slit through the channel for the lens tab. For corrosive liquids, leave out all vent holes. Ours: a compression mould.

مواد مورد نیاز این مرحله:

آمیزه لاستیکیآمیزه لاستیکی1 frame

ابزارهای مورد نیاز:

قالب فشاریقالب فشاری
ابعاد نامعلومابعاد نامعلوم
2

Cut the lens

Cut one lens from flexible clear plastic, shaped to match the rim. The patent tested cellulose acetate. Leave a tab at each end, outside the area you look through. Cut a closed slot in each tab and line it with a grommet. Make two holes at the centre for the bolts. Leave no other holes in the viewing area.

مواد مورد نیاز این مرحله:

ورق پلاستیک شفافورق پلاستیک شفاف1 lens
حلقه پرچحلقه پرچ2 tab grommets

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
سنبهٔ نشانه‌گذاریسنبهٔ نشانه‌گذاری
3

Seal the lens in the frame

Spring the lens edge into the channel all the way round, pushing each tab out through its slit so it lies under the lug, slot over slot. Fasten the centre with two stainless-steel bolts and nuts. (The vented version uses snap fasteners here.)

مواد مورد نیاز این مرحله:

پیچ‌های ماشینیپیچ‌های ماشینی2 stainless steel
مهرهٔ شش‌گوشمهرهٔ شش‌گوش2 stainless steel

ابزارهای مورد نیاز:

مجموعه پیچ‌گوشتیمجموعه پیچ‌گوشتی
4

Fit the head strap

Use a strap in two halves, joined at the back by a buckle, each half with a thickened end. Slide a slotted plate of metal or plastic onto each half, then thread it from the front through the lug slot and the lens-tab slot. The thick end stops against the plate and lug. The pull of the strap now goes into both lens and frame, holds the lens in, and stays outside the field of view.

مواد مورد نیاز این مرحله:

بند سر عینک ایمنیبند سر عینک ایمنی1 two halves
سگک برنجی با زبانهسگک برنجی با زبانه1 قطعه
ماده ناشناختهماده ناشناخته1 two slotted plates

ابزارهای مورد نیاز:

ابعاد نامعلومابعاد نامعلوم

مواد

8

ابزارهای لازم

5

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...