همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنیها

Digital Tachometer: Hand-Held Contact Type That Holds Its Reading (Sugiyama, Shimpo, US 4,000,465, 1976)
A hand-held digital tachometer. You press the contact head on its shaft against the end of a turning shaft and push the thumb button; a slotted disk inside chops a light beam into pulses, and the pulses counted in a fixed time, set by a quartz clock, appear in the window as the speed. A latch holds the reading after you take the tachometer away, so you can read it even where you could not see the window while measuring.
Result: a contact tachometer that shows revolutions per unit time and keeps the last reading.
Source: Y. Sugiyama (Shimpo Kogyo), US 4,000,465 (1976). Unknown: the number of holes, the clock, the gate time and the circuit details. Picture: the patent drawing.
پیشرفته
Unknown
دستورالعملها
1
1
Make the housing and measuring shaft
Make the housing and measuring shaft
Make a cylindrical housing to hold in one hand, with a window in its side for the reading and a push button for the power switch where the thumb falls. Run a measuring shaft out of the front end in bearings and fit a contact head on its tip to press against the shaft being measured. Not given: materials, sizes. Ours: aluminium tube, a ball bearing.
مواد مورد نیاز این مرحله:
لوله آلومینیومی1 housing
فلز نامعلوم1 measuring shaft
بلبرینگ1 قطعه
ماده ناشناخته1 contact headابزارهای مورد نیاز:
تراش فلز
دریل دستی
ابعاد نامعلوم2
2
Make the pulse generator
Make the pulse generator
Fix a disk on the measuring shaft with a ring of small holes evenly spaced near its edge. Put a light source on one side of the disk and a photodetector on the other: each hole passing makes one pulse. Shape and amplify the pulses. Not given: the number of holes. Ours: an LED and a photodiode.
مواد مورد نیاز این مرحله:
ماده ناشناخته1 slotted disk
مجموعهٔ الایدی1 light source
فوتودیود (BPW34)1 photodetector
مقاومت1 مجموعهابزارهای مورد نیاز:
دریل دستی3
3
Build the counting circuit
Build the counting circuit
Divide a quartz oscillator's clock down to gate pulses one unit of time long. Pass the measurement pulses through an AND gate during each gate pulse into a counter. At the start of each gate pulse a reset pulse clears the counter. After the gate pulse ends, the first measurement pulse that arrives triggers a latch pulse that loads the new count into the display. If the head has been taken off the shaft, no pulse arrives, no latch pulse is made, and the display keeps the last reading until the next measurement or until the power is switched off. Not given: the clock frequency and gate time. Ours: logic ICs and a seven-segment display.
مواد مورد نیاز این مرحله:
برد مدار چاپی1 قطعه
کریستال کوارتز1 قطعه
مجموعهٔ آیسی منطقی1 divider, AND gate, counter, latch, reset
درایور نمایشگر هفتقطعهای1 قطعه
نمایشگر هفتقطعهای چهار رقمی1 قطعه
سیم لحیم1 as neededابزارهای مورد نیاز:
هویه4
4
Power it and measure
Power it and measure
Fit the battery and the thumb button as the power switch. Press the contact head against the end of the turning shaft so it turns with it, push the button, and read the revolutions in the window, now or after you take the tachometer away.
مواد مورد نیاز این مرحله:
باتری1 قطعه
کلید فشاری1 قطعهابزارهای مورد نیاز:
هویهمواد
15- 1 housingجایگزین
- 1 measuring shaftجایگزین
- جایگزین
- 1 slotted diskجایگزین
- 1 light sourceجایگزین
- 1 photodetectorجایگزین
- 1 مجموعهجایگزین
- 1 قطعهجایگزین
- 1 قطعهجایگزین
- 1 divider, AND gate, counter, latch, resetجایگزین
- جایگزین
- جایگزین
- 1 as neededجایگزین
- 1 قطعهجایگزین
- جایگزین
مواد نقشههای متصل
این نقشه میسازد
CC0 مالکیت عمومی
این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.
با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت میکند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

