همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Distillation Column Assembly: Flask, "Evaporator" Still-Head, Liebig Condenser and Receivers (Young, 1903)
Charlie

ایجاد شده توسط

Charlie

3. نوامبر 2026DE
۱۰
۰
۰
۰
۰

Distillation Column Assembly: Flask, "Evaporator" Still-Head, Liebig Condenser and Receivers (Young, 1903)

A complete fractional distillation set: a globular flask, Young and Thomas's 'evaporator' still-head built of stacked glass sections, a Liebig condenser and a row of receivers. In each section the rising vapour is forced through the liquid running back down, so the mixture separates better at each step. Result: a fractionating apparatus for separating liquids by boiling point, the fractions caught in receivers changed at set temperatures. Source: S. Young, Fractional Distillation (1903), pp. 4-7, 115-116, 166-168. Picture: Figs. 37 and 38 of the book.
پیشرفته
Unknown

دستورالعمل‌ها

1

Choose the still

Use a globular flask, since a flat-bottomed one may crack over a naked flame, no larger than the amount of liquid needs. Fit it with a cork for the still-head. Ours: a round-bottom flask.

مواد مورد نیاز این مرحله:

بالن ته‌گردبالن ته‌گرد1 still
چوب‌پنبه‌هاچوب‌پنبه‌ها1 still cork

ابزارهای مورد نیاز:

چراغ بونزنچراغ بونزن
2

Blow the evaporator still-head

Build the still-head of sections joined end to end. Each outer tube is 22 to 24 mm inside and about 10 to 10.5 cm long, constricted at the bottom. In it stands a thin inner tube, 7.5 to 8 mm inside and 60 mm long, open at both ends, with two large holes near its top. Its lower end widens into a funnel resting on the constriction, with three or four tiny glass beads fused to the rim so it does not fit too tightly. Over it stands an intermediate tube about 14 mm inside and 50 mm long, like a small inverted test tube. A small funnel, slightly wider than the dip in the outer tube above, sits on top of it on three glass legs. Small glass projections centre the tubes. Make the head long enough that the thermometer's bulb and stem both sit in the vapour, with a side delivery tube at the top.

مواد مورد نیاز این مرحله:

لوله شیشه‌ایلوله شیشه‌ای1 sections, inner and intermediate tubes, delivery tube

ابزارهای مورد نیاز:

مشعل شیشه‌گری رومیزیمشعل شیشه‌گری رومیزی
3

Fit the condenser

Use a Liebig condenser, about 7 or 8 mm inside for the inner tube and 15 mm for the outer, cooled by running water. Pass the delivery tube through a cork into it. Draw out the joint where the wide inlet meets the narrow tube so no pool of liquid lies there. Bend the narrow tube so the condenser can stand upright. Above about 170 °C use a long tube cooled by air instead of water.

مواد مورد نیاز این مرحله:

مبرد آبیمبرد آبی1 condenser
چوب‌پنبه‌هاچوب‌پنبه‌ها1 condenser cork

ابزارهای مورد نیاز:

مشعل شیشه‌گری رومیزیمشعل شیشه‌گری رومیزی
آبآب
4

Set the heat and the receivers

Heat with a Bunsen burner, its top about 2 mm below the flask so the small flame touches the glass, shielded from draughts. Add a few pieces of porous porcelain (a broken clay pipe will do) or pumice if the liquid bumps. Set a thermometer in the still-head and a row of small flasks as receivers.

مواد مورد نیاز این مرحله:

دماسنجدماسنج1 still-head thermometer
بالن جمع‌آوریبالن جمع‌آوری10 receivers

ابزارهای مورد نیاز:

چراغ بونزنچراغ بونزن
ماده ناشناختهماده ناشناخته
5

Distil in fractions

Read the barometer and correct the set temperatures for it. Distil steadily. In each section, condensed liquid seals the narrow passage, so the vapour rises up the inner tube, down between the tubes and up again, while liquid drips from section to section back to the still. Collect the distillate in fractions, changing the receiver each time the temperature reaches one of the values fixed beforehand.

ابزارهای مورد نیاز:

فشارسنج جیوه‌ایفشارسنج جیوه‌ای
چراغ بونزنچراغ بونزن
آبآب

مواد

6
  • جایگزین
  • 1 condenser cork
    جایگزین
  • 1 sections, inner and intermediate tubes, delivery tube
    جایگزین
  • 1 condenser
    جایگزین
  • 1 still-head thermometer
    جایگزین
  • جایگزین

ابزارهای لازم

5

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...