هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights
Penny

ایجاد شده توسط

Penny

14. اکتبر 2026DK
۲۵
۰
۰
۰
۰

Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights

The oldest weighing machine is a beam with equal arms balanced on a pivot, a pan hanging from each end: put the load in one pan and known weights in the other until the beam lies level. Balances go back to the Fourth Dynasty of Egypt. A hardened knife edge makes it sensitive and a long pointer shows the smallest tilt; the weights are cast in brass and adjusted against each other. The picture: our diagram of the balance, its knife edge, pointer, pans and weights.
متوسط
Two to three days

دستورالعمل‌ها

1

Beam and knife edge

File a straight beam from flat tool steel with a hole exactly in the middle and one near each end, the two end holes equally far from the centre. Forge and file a short steel knife edge, harden and temper it, and fit it through the centre hole, edge down. File a long pointer onto the beam.

مواد مورد نیاز این مرحله:

تسمهٔ فولاد ابزارتسمهٔ فولاد ابزار1 قطعه

ابزارهای مورد نیاز:

سوهان فلزسوهان فلز
دریل دستیدریل دستی
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
کورهٔ آهنگریکورهٔ آهنگری
سطل آب‌دهیسطل آب‌دهی
عینک ایمنیعینک ایمنی
2

Stand and bearing

Make an upright stand of hardwood with a hardened steel V-block on top, shallower than the knife edge, so the beam rocks freely. Mark a zero line behind the pointer.

مواد مورد نیاز این مرحله:

نوارِ چوب سختنوارِ چوب سخت2 قطعه
میلگرد فولاد نرممیلگرد فولاد نرم0.3 m

ابزارهای مورد نیاز:

سوهان فلزسوهان فلز
کورهٔ آهنگریکورهٔ آهنگری
سطل آب‌دهیسطل آب‌دهی
3

Pans

Cut two equal brass discs, dish them slightly, drill three holes in each rim and hang each from an end hole on three equal cords.

مواد مورد نیاز این مرحله:

ورق برنجورق برنج1 قطعه
نخ کتان مومینخ کتان مومی3 m

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
دریل دستیدریل دستی
سوهان فلزسوهان فلز
4

Trim to level

With both pans empty, file the heavier side until the pointer rests on zero. Swap the pans and check again: if the pointer moves, the arms are unequal and the end holes need moving.

ابزارهای مورد نیاز:

سوهان فلزسوهان فلز
5

Cast the weights

Melt brass and cast a row of plain cylinders a little heavy in green sand.

مواد مورد نیاز این مرحله:

شمش برنجشمش برنج2 کیلوگرم
زغال چوبزغال چوب1 as required
ماسهٔ ریخته‌گریماسهٔ ریخته‌گری5 کیلوگرم

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
بوتهٔ گِل نسوزبوتهٔ گِل نسوز
انبر بوتهانبر بوته
جعبه قالب ریخته‌گری (بالا و پایین)جعبه قالب ریخته‌گری (بالا و پایین)
دستکش جوشکاریدستکش جوشکاری
6

Adjust the weights

Balance the largest weight against a litre of water measured in the cylinder (one kilogram, our reference), filing it down until the beam is level. Make the smaller ones by balancing pairs against a larger one and against each other, filing each to level.

مواد مورد نیاز این مرحله:

آبآب1 لیتر

ابزارهای مورد نیاز:

استوانهٔ مدرّجاستوانهٔ مدرّج
سوهان فلزسوهان فلز
7

A binary set of weights

در حال بارگذاری دفترچهٔ Jupyter…
8

Limits

The balance's form and use are as Wikipedia describes; the sizes and the water reference are ours. Water's density changes a little with temperature, so the reference is good to a few parts in a thousand.

مواد

9

ابزارهای لازم

12

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...