همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Fume Hood (Ducted): Sloping Stone Baffle Set from Outside by a Crank (Liptay, US 2,779,265, 1957)
Penny

ایجاد شده توسط

Penny

3. نوامبر 2026DK
۱۴
۰
۰
۰
۰

Fume Hood (Ducted): Sloping Stone Baffle Set from Outside by a Crank (Liptay, US 2,779,265, 1957)

A bench fume hood on a stone counter, drawn off through a duct with a fan. Inside, a sloping stone baffle leaves a gap at the top and one at the bottom. A crank under the counter slides the baffle: one gap grows as the other shrinks, so the air sweeps light fumes out at the top or heavy fumes out at the bottom, with no one reaching inside. Result: a ducted hood whose air flow can be set for light or heavy fumes during work. Source: J. M. Liptay, US 2,779,265 (1957). Unknown: sizes, air flow, the fan and most materials. Picture: the patent drawing.
پیشرفته
Unknown

دستورالعمل‌ها

1

Build the cabinet and stone counter

Build a sheet metal cabinet. Fix spaced sheet metal channels to its front panel and rear wall, and lay a stone slab on them as the counter. Bore a hole through the slab near the back, at the middle, for the baffle's lifting rod. Not given: sizes, the metal.

مواد مورد نیاز این مرحله:

فلز نامعلومفلز نامعلوم1 cabinet and channels
لوح سنگی تختلوح سنگی تخت1 counter

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
دریل ستونیدریل ستونی
ابعاد نامعلومابعاد نامعلوم
2

Build the hood

On the counter, make a frame of corner angle irons. Fix to it two sides, a rear wall, a roof and a front panel. Leave the front open below the front panel: this is the large opening where you work and where air comes in. Cut the fume outlet in the roof, towards the back. Not given: the panel material, sizes.

مواد مورد نیاز این مرحله:

نبشی فولاد نرمنبشی فولاد نرم1 corner frame
ماده ناشناختهماده ناشناخته1 sides, rear wall, roof, front panel

ابزارهای مورد نیاز:

ارهٔ آهن‌برارهٔ آهن‌بر
ابعاد نامعلومابعاد نامعلوم
3

Fit the exhaust pipe and fan

Fix an exhaust pipe over the roof outlet, with a fan in it, to draw the fumes out. Not given: the pipe, the fan, the air flow.

مواد مورد نیاز این مرحله:

کانال‌های هواکانال‌های هوا1 exhaust pipe
دمندهٔ هوادمندهٔ هوا1 fan

ابزارهای مورد نیاز:

آچار فرانسهآچار فرانسه
4

Fit the sloping baffle

Make a solid stone baffle almost as wide as the hood. Set it sloping up and forward from the rear wall, so it splits the inside into the work space in front and a duct behind that widens upward to the outlet. Guide it on sloping rails in front and strips behind, fixed to the sides, so it can slide. Leave a gap between its top and the roof, and one between its bottom and the counter. Not given: the rails' metal, sizes.

مواد مورد نیاز این مرحله:

لوح سنگی تختلوح سنگی تخت1 baffle
فلز نامعلومفلز نامعلوم1 rails and strips

ابزارهای مورد نیاز:

ابعاد نامعلومابعاد نامعلوم
5

Make the lifting rod

Cut a notch in the middle of the baffle's lower edge. Make a V-shaped yoke whose legs straddle the baffle front and back, rivet the legs to it, and give the yoke a rod that hangs down through the hole in the counter. Thread the rod's lower end. Not given: the metal.

مواد مورد نیاز این مرحله:

فلز نامعلومفلز نامعلوم1 yoke, rod, rivets

ابزارهای مورد نیاز:

مجموعهٔ پرچمجموعهٔ پرچ
مجموعه قلاویز و حدیدهمجموعه قلاویز و حدیده
6

Fit the bell crank

Under the counter, pivot a bell crank lever on a bolt through the lugs of a bracket fixed to the cabinet's rear channel. Screw a coupling onto the rod's threaded end. The coupling's two curved lips rock on the lever's long arm, and its tongue hangs through a slot in the arm, held by a cotter pin. On the short arm, a yoke turns on two bolts set fast in the threaded cross-holes of a round nut. Ours: hex bolts and nuts.

مواد مورد نیاز این مرحله:

اهرم زاویه‌داراهرم زاویه‌دار1 bell crank
فلز نامعلومفلز نامعلوم1 bracket, coupling, round nut
مجموعهٔ پیچ‌های شش‌گوشمجموعهٔ پیچ‌های شش‌گوش3 قطعه
مهرهٔ شش‌گوشمهرهٔ شش‌گوش1 قطعه
اشپیلاشپیل1 قطعه

ابزارهای مورد نیاز:

مجموعه قلاویز و حدیدهمجموعه قلاویز و حدیده
آچار فرانسهآچار فرانسه
7

Fit the crank and set the baffle

Screw a metal operating rod through the round nut and run it forward to the cabinet front. Screw its front socket onto the shaft of a hand crank and pin it with a cotter pin. Weld an angle iron to the inside of the front panel to stiffen it. Clamp a bushing through the panel with a nut, and set a ball bearing between two rings on the shaft, between the bushing and the crank. Turning the crank tips the bell crank, which raises the rod and baffle or lets them slide down by their own weight: as one gap grows the other shrinks. Air comes in at the front; the upper stream carries light fumes to the top gap, the lower stream heavy fumes to the bottom gap. Open the top fully for light fumes, the bottom fully for heavy ones, or set any point between, without reaching inside. A sliding safety sash may be fitted over the front opening, to watch dangerous reactions safely.

مواد مورد نیاز این مرحله:

فلز نامعلومفلز نامعلوم1 operating rod, crank, bushing
اشپیلاشپیل1 قطعه
مهرهٔ شش‌گوشمهرهٔ شش‌گوش1 قطعه
نبشی فولاد نرمنبشی فولاد نرم1 stiffener
بلبرینگ کف‌گردبلبرینگ کف‌گرد1 قطعه

ابزارهای مورد نیاز:

دستگاه جوشکاری قوس الکتریکیدستگاه جوشکاری قوس الکتریکی
مجموعه قلاویز و حدیدهمجموعه قلاویز و حدیده
آچار فرانسهآچار فرانسه

مواد

11

ابزارهای لازم

8

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...