همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)
Forge

ایجاد شده توسط

Forge

13. نوامبر 2026NO
۱۰
۰
۰
۰
۰

Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)

Henry Gibbs of Chicago received US 683,645, dated 1 October 1901, for a lawn sprinkler "operating on the familiar Barker's mill principle": water leaving its arms sideways pushes the head round. His head turns on a ring of steel balls held in matching grooves in the head and in the end of the supply pipe, so it spins freely with little friction and stays on. We turn the head from brass and the groove in a steel pipe on the lathe. All sizes are ours.
متوسط
About 5 hours

دستورالعمل‌ها

1

How many balls

در حال بارگذاری دفترچهٔ Jupyter…
2

Read US 683,645

"It being only necessary that certain of the orifices shall discharge the water tangentially to revolve the head 14 and spray-pipes 15 in the well-known manner."
3

Groove the supply pipe

Chuck a length of steel pipe (his pipe 13) and finish its top end smooth and round. Cut a half-round groove (his 17) round it a little below the end, to the depth the notebook gives, with a round-nosed tool. Use thick-walled pipe, so at least 1.5 mm of wall is left under the groove (ours).

مواد مورد نیاز این مرحله:

لوله فولادی (جدارضخیم، با سرهای رزوه‌دار)لوله فولادی (جدارضخیم، با سرهای رزوه‌دار)1 قطعه

ابزارهای مورد نیاز:

تراش فلزتراش فلز
سه‌نظام تراشسه‌نظام تراش
رندهٔ تراشکاریرندهٔ تراشکاری
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
4

Turn the head

Turn a brass bar to a short round head (his 14). Bore it from below to loosely fit the pipe end, his bore 16, but stop short of the top so a lip (his flange 22) overhangs the pipe end. Cut a matching groove 18 inside the bore at the same height as the pipe's groove.

مواد مورد نیاز این مرحله:

میلگرد گرد برنجیمیلگرد گرد برنجی1 قطعه

ابزارهای مورد نیاز:

تراش فلزتراش فلز
سه‌نظام تراشسه‌نظام تراش
رندهٔ تراشکاریرندهٔ تراشکاری
مجموعه مته مرغکمجموعه مته مرغک
مجموعه متهمجموعه مته
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
5

Drill the ball hole and the arms

Drill a hole (his opening 20) through the head's side into the groove, just bigger than a ball, and tap it for a screw plug (21). Drill three holes round the head into the bore for the spray pipes.

ابزارهای مورد نیاز:

دریل ستونیدریل ستونی
مجموعه متهمجموعه مته
مجموعه قلاویز و حدیدهمجموعه قلاویز و حدیده
گیرهٔ رومیزیگیرهٔ رومیزی
6

Make the spray pipes

Cut three lengths of copper tube, close their outer ends, and bend the last bit of each upward as his Fig. 1. Drill small holes near the ends, some pointing sideways (tangentially), all the same way round, so the jets turn the head. Solder the pipes into the head's holes (ours; he threads them in).

مواد مورد نیاز این مرحله:

لولهٔ مسیلولهٔ مسی1 قطعه
لحیم قلع-سربلحیم قلع-سرب1 قطعه
فلاکس لحیمفلاکس لحیم1 قطعه

ابزارهای مورد نیاز:

ارهٔ آهن‌برارهٔ آهن‌بر
مجموعه متهمجموعه مته
دریل ستونیدریل ستونی
هویه برقیهویه برقی
گیرهٔ رومیزیگیرهٔ رومیزی
7

Assemble with the balls

Slide the head onto the pipe end with the grooves level. Feed balls in through the side hole, turning the head, until the race is full; then screw in the plug. The head should spin freely and not lift off.

مواد مورد نیاز این مرحله:

بلبرینگ‌های فولادیبلبرینگ‌های فولادی1 قطعه
پیچ‌های ماشینیپیچ‌های ماشینی1 قطعه

ابزارهای مورد نیاز:

آچار فرانسهآچار فرانسه
8

Make the stand

Bore a hardwood block to hold the pipe upright and glue in three splayed dowel legs (ours; his base 10 and supports 11). Screw the hose coupling onto the pipe's lower end below the block (his coupling 12).

مواد مورد نیاز این مرحله:

قطعهٔ چوب سختقطعهٔ چوب سخت1 قطعه
میخ‌های چوب سختمیخ‌های چوب سخت1 قطعه
چسب چوبچسب چوب1 قطعه
کوپلینگ شلنگکوپلینگ شلنگ1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
دریل ستونیدریل ستونی
مجموعه متهمجموعه مته
9

Run it

Connect a garden hose and turn on the water slowly: the jets push the head round and throw the water in a circle. More pressure turns it faster.
10

Troubleshooting

Lawn sprinkler troubleshooting.

Flow

Loading...
11

History and honest limits

**Henry Gibbs** of Chicago, assignor to W. D. Allen Manufacturing Company, US 683,645, dated 1 October 1901, filed 20 May 1901. He claimed a single-piece hollow coupling with radial spray pipes having tangential orifices, a bore loosely fitting the supply pipe, "annular grooves in the opposed cylindrical faces of said bore and said pipe" and "bearing balls interposed in said grooves". He gives no sizes or metals; the brass, steel pipe, ball size, soldered copper arms and the wooden stand are ours.

مواد

11

ابزارهای لازم

13

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...