همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Hackle Combs: Coarse and Fine Flax Heckles on One Board (Ure, 1839)
Woody

ایجاد شده توسط

Woody

4. نوامبر 2026NO
۱۲
۰
۰
۰
۰

Hackle Combs: Coarse and Fine Flax Heckles on One Board (Ure, 1839)

A pair of flax heckles on one oblong plank: two round wooden blocks, each faced with a drilled brass or iron plate holding upright iron teeth. Flax is drawn first through the coarse heckle, then through the fine one, splitting the fibres, combing out the short tow and laying the long fibres straight. Coarse: teeth about 1/10 in thick and 1 1/4 in long, a centre tooth and 12 rings, the outer ring 5 3/4 in across. Fine: thinner teeth set closer, 1109 of them. Source: Andrew Ure, Dictionary of Arts, Manufactures and Mines (1839), 'Flax'. Picture: Figs. 424-425 of the book.
متوسط
Unknown

دستورالعمل‌ها

1

Make the board and blocks

Cut an oblong plank (Fig. 424, a b) and two round (or square) wooden blocks, c for the coarse heckle and d for the fine, and fix the blocks on the plank (Fig. 425). The heckles can also be made on separate boards.

مواد مورد نیاز این مرحله:

الوار چوب سختالوار چوب سخت1 قطعه
قطعهٔ چوب سختقطعهٔ چوب سخت2 قطعه
پیچ چوبپیچ چوب1 قطعه

ابزارهای مورد نیاز:

اره پشت‌داراره پشت‌دار
پیچ‌گوشتی تختپیچ‌گوشتی تخت
2

Drill the face plates

Cover the top of each block with a brass or iron plate drilled for the teeth, which gives them a firmer hold. Set the holes evenly over the whole face, in concentric circles (the German way) or parallel rows (the English way). Coarse: a centre hole and 12 rings, the outermost 5 3/4 in across. Fine: thinner holes set closer, 1109 in all.

مواد مورد نیاز این مرحله:

ورق برنجورق برنج2 face plates

ابزارهای مورد نیاز:

پرگار دوسرپرگار دوسر
قیچی ورق‌بریقیچی ورق‌بری
دریل دستیدریل دستی
3

Make the teeth

Cut teeth of iron (sometimes steel) 1 to 2 in long. For the coarse heckle make them about 1/10 in thick and 1 1/4 in long, tapering from the middle to a very fine point; the fine heckle's teeth are thinner. File every point sharp and smooth, running evenly into the round stem like a sewing needle; square points in a rhombus shape cut the fibres apart better than round ones.

مواد مورد نیاز این مرحله:

سیم آهنیسیم آهنی1 teeth

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
سوهان فلزسوهان فلز
4

Set the teeth

Drive each tooth through its hole in the plate into the block so it stands upright, all points at one level.

ابزارهای مورد نیاز:

چکشچکش

مواد

5
  • جایگزین
  • جایگزین
  • 1 قطعه
    جایگزین
  • 2 face plates
    جایگزین
  • جایگزین

ابزارهای لازم

7

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...