همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Riding Saddle: Web, Stuffed Seat, Hogskin Skirts, Knee-Pad Flaps and Quilted Panel on a Bought Tree (Hasluck, Saddlery, 1904)
Tex

ایجاد شده توسط

Tex

13. نوامبر 2026FO
۴
۰
۰
۰
۰

Riding Saddle: Web, Stuffed Seat, Hogskin Skirts, Knee-Pad Flaps and Quilted Panel on a Bought Tree (Hasluck, Saddlery, 1904)

A riding saddle from Paul N. Hasluck's Saddlery (1904), the "gentleman's riding saddle" of the English trade: on a bought tree, a seat of stretched web and linen, stuffed with carded flock and covered in hogskin, hogskin-covered skirts, flaps with stuffed knee-pads, a corded gullet piece, girth straps, and a quilted panel underneath. All sizes are his. It is an English saddle, not a Western stock saddle; no public-domain source for a Western saddle was found.
پیشرفته
About 1 week

دستورالعمل‌ها

1

How much straining web

در حال بارگذاری دفترچهٔ Jupyter…
2

Read Saddlery, ch. I

"In making a gentleman's riding saddle, the first article needed is a tree (Fig. 1), which can be bought with a round cantle (the back rising part) or with a square one rounded at the corners, and running in a straight line at the top."
3

Stretch the web

Damp the straining web and nail each end firmly to a board, then push something underneath to stretch it to the utmost. Let it dry; damp it once or twice more as needed, letting it dry between.

مواد مورد نیاز این مرحله:

نوار کششنوار کشش1 قطعه

ابزارهای مورد نیاز:

تختهٔ کاجتختهٔ کاج
میخمیخ
چکش دوشاخچکش دوشاخ
اسفنجاسفنج
4

Web the tree

Cut the web in two and nail two ends at the head of the tree just outside the iron plate, slanting one to each side. Pull them tight and nail them at the back low under the cantle, which throws them 5 to 6 in apart at the back; nail them down closely with headed saddle tacks. Tack the other piece across close to the saddle bar, a little under where the bar is riveted, with 4 in hanging down each side, pulled very tight. Lay another piece of web ("any diaper web will do") close behind and nail it tight, and run a stitch from one web to the other.

مواد مورد نیاز این مرحله:

قالب زین سواریقالب زین سواری1 قطعه
نوار کششنوار کشش1 قطعه
میخمیخ1 قطعه
نخ چرمینخ چرمی1 قطعه

ابزارهای مورد نیاز:

گازانبرگازانبر
چکش دوشاخچکش دوشاخ
درفشدرفش
دو سوزن سراجیدو سوزن سراجی
5

Lay the seat foundation

Stitch a piece of strong linen across to the web, large enough to run all round the seat behind, and nail it round the sides and back, covering the web ends; pull it tight and nail it so the seat will rise toward the cantle when stuffed. Stitch another piece to the web in front and nail it all round, so the seat is covered without hollow.

مواد مورد نیاز این مرحله:

پارچهٔ کتانپارچهٔ کتان1 قطعه
میخمیخ1 قطعه
نخ چرمینخ چرمی1 قطعه

ابزارهای مورد نیاز:

چکش دوشاخچکش دوشاخ
درفشدرفش
دو سوزن سراجیدو سوزن سراجی
6

Make the side pads

Double a piece of basil about 6 in long along the centre, pointed at one end and full at the other. Stitch the edges, leave a small opening and stuff it smoothly and tightly with flock: a little thicker than the middle finger at the full end, tapering to a fine point. Close it and flatten it slightly with the mallet. Nail one each side flush with the edge of the tree, thick end against the cantle.

مواد مورد نیاز این مرحله:

تیماج گوسفندی (بازیل)تیماج گوسفندی (بازیل)1 قطعه
پشم پرکنپشم پرکن1 قطعه
میخمیخ1 قطعه

ابزارهای مورد نیاز:

دو سوزن سراجیدو سوزن سراجی
چکش چوبیچکش چوبی
چکش دوشاخچکش دوشاخ
7

Cover and stuff the seat

Cover the seat with white serge, nailed over the cantle edge, under the gullet in front and under the sides to the hanging web; from there forward back-stitch it coarsely to the shape of skirt and seat. Back-stitch it through the tree along the side pads. Rub a patch about 2½ x 1 in in the centre with black wax and cut a 1½ in slit in it. Pass a pound of white flock through the carding machine three or four times, clip long wool, and stuff it in with the seat iron, a little at a time, moving it to the sides, until firm and level; level it with the seat awl, feeling with the left hand, and stitch the opening.

مواد مورد نیاز این مرحله:

سرژ پشمیسرژ پشمی1 قطعه
موم کفاشیموم کفاشی1 قطعه
پشم پرکنپشم پرکن1 قطعه
میخمیخ1 قطعه
نخ چرمینخ چرمی1 قطعه

ابزارهای مورد نیاز:

قیچیقیچی
دستگاه حلاجی پشم پرکندستگاه حلاجی پشم پرکن
آهن نشیمنآهن نشیمن
درفشدرفش
دو سوزن سراجیدو سوزن سراجی
چکش دوشاخچکش دوشاخ
8

Cover the seat in hogskin

Cut the seat from good hogskin large enough to be nailed underneath. Damp it and nail it on smooth, underneath at the sides and back, so the nails pull out easily and leave no mark. Gather the small pleats behind the cantle into two large ones, one each side of the crupper staple, to be cut and stitched when dry. Let it dry.

مواد مورد نیاز این مرحله:

چرم خوکچرم خوک1 قطعه
میخمیخ1 قطعه

ابزارهای مورد نیاز:

کارد چرم‌بریکارد چرم‌بری
اسفنجاسفنج
چکش دوشاخچکش دوشاخ
9

Make the skirts

Cut the skirts to his Fig. 3 from flat brown skirt leather. Cut a strip of hogskin belly to run 1 in in from the edge along the under part, to within 4 in of the narrow point and 1½ in beyond in front, low enough to nail under the tree; paste linen on its flesh side. Raise holes along the skirt's edge with a bent awl, not through. Cover the skirt with pasted hogskin (or paste serge on to within ¼ in of the edge and cover without pasting), stitch it fine near the edge with yellow hemp, silk or white linen thread and beeswax, run a row ¾ in from the top, and finish. When dry, stitch the nailing piece through the raised holes with fine beeswax thread.

مواد مورد نیاز این مرحله:

چرم دامن زینچرم دامن زین2 قطعه
چرم خوکچرم خوک1 قطعه
پارچهٔ کتانپارچهٔ کتان1 قطعه
چسب آرد گندمچسب آرد گندم1 قطعه
نخ کتاننخ کتان1 قطعه
موم زنبور عسلموم زنبور عسل1 قطعه

ابزارهای مورد نیاز:

کارد چرم‌بریکارد چرم‌بری
درفش خمیدهدرفش خمیده
درفشدرفش
دو سوزن سراجیدو سوزن سراجی
10

Make the flaps and knee-pads

Cut the flaps in pairs, grain side out underneath. On the front of each, spot a serge cover for a knee-pad, from the point of the skirt to the bottom, shaped to the flap outside and straight inside to within 3 in of the top. Nail the flap to the flap (shafteau) block through each end of the pad and stuff it full and evenly, "full in front and sloping towards the inside". Add a small flat pad at the top corner of the other side. Paste damped hogskin over the pads, pulled tight, with a band of leather along the pad's straight side and a smooth string nailed along the front to pull the hogskin into the hollow; dry on the block. Trim the hogskin to the edge, stitch it all round, level the edges with sandpaper and polish.

مواد مورد نیاز این مرحله:

چرم دامن زینچرم دامن زین2 قطعه
سرژ پشمیسرژ پشمی1 قطعه
پشم پرکنپشم پرکن1 قطعه
چرم خوکچرم خوک1 قطعه
چسب آرد گندمچسب آرد گندم1 قطعه
بندبند1 قطعه
نخ کتاننخ کتان1 قطعه

ابزارهای مورد نیاز:

کارد چرم‌بریکارد چرم‌بری
قالب بال زینقالب بال زین
میخمیخ
درفشدرفش
دو سوزن سراجیدو سوزن سراجی
کاغذ سنبادهکاغذ سنباده
اسفنجاسفنج
11

Join seat and skirts

Tack both skirts in place on the seat, mark a line along the seat at the skirt edge and mark matching points. Cut the seat along the mark. Whip a dogskin welt, 1 in longer than the skirt each end, to the skirt's top edge with single linen thread, regular stitches. Damp the edges and back-stitch seat to skirt through the same holes, marks opposite, catching a piece of hogskin seat at the 4 in near the narrow part. Cut and stitch the two pleats behind the cantle from underneath, half through the leather. Cover the tree points beyond the bars with pasted thin basil or hogskin.

مواد مورد نیاز این مرحله:

چرم سگچرم سگ1 قطعه
نخ کتاننخ کتان1 قطعه
تیماج گوسفندی (بازیل)تیماج گوسفندی (بازیل)1 قطعه
چسب آرد گندمچسب آرد گندم1 قطعه

ابزارهای مورد نیاز:

کارد چرم‌بریکارد چرم‌بری
دو سوزن سراجیدو سوزن سراجی
درفشدرفش
اسفنجاسفنج
12

Put seat and skirts on the tree

Damp the seat all over, keeping it from iron stains. Nail the front over the gullet under the tree with the skirts level, nail it behind by the iron plate and slit it over the crupper staple, pulling with small pincers. Fasten the sides with nails driven alternately so it is square and straight. Slit the leather opposite the hanging web, pull it tight with pincers and nail through both into the tree; trim the web and waste close to the nails.

مواد مورد نیاز این مرحله:

میخمیخ1 قطعه

ابزارهای مورد نیاز:

اسفنجاسفنج
گازانبرگازانبر
چکش دوشاخچکش دوشاخ
کارد چرم‌بریکارد چرم‌بری
13

Fit the flaps

Cut a nick upward in the front of each flap to run above the tree point; pass the rest under the tree behind the bar, cut above the hanging web, round the end and nail it under the tree close to the skirt; stitch through the web piece. Drive a tough silver nail through the top of the knee-pad and clinch it underneath, another in the front of the other flap, and one behind each side below the seat pad, slanting through the tree and clinched.

مواد مورد نیاز این مرحله:

میخ زینمیخ زین4 قطعه
میخمیخ1 قطعه
نخ چرمینخ چرمی1 قطعه

ابزارهای مورد نیاز:

کارد چرم‌بریکارد چرم‌بری
چکش دوشاخچکش دوشاخ
درفشدرفش
دو سوزن سراجیدو سوزن سراجی
14

Make the gullet piece

Cut brown leather 1 in wide to run round the front of the gullet from flap point to flap point, and hogskin a little wider. Stitch the hogskin on along the edge, damp it, push a cord in close to the stitches and paste the hogskin down. Punch a hole about 1¼ in below where seat and skirt join, slit it inward, and nail it along the gullet so the cord lies tight against the tree's edge, slits equal each side; raise the parts below to meet the flap ends and nail and stitch them. Put two silver saddle staples through flap point, gullet piece and tree, knock them down and clinch them; cover the nails with a pasted oval of thinned hogskin.

مواد مورد نیاز این مرحله:

چرم یراقچرم یراق1 قطعه
چرم خوکچرم خوک1 قطعه
بندبند1 قطعه
چسب آرد گندمچسب آرد گندم1 قطعه
منگنهٔ زینمنگنهٔ زین2 قطعه
میخمیخ1 قطعه
نخ کتاننخ کتان1 قطعه

ابزارهای مورد نیاز:

کارد چرم‌بریکارد چرم‌بری
منگنهٔ سوراخ‌کن چرممنگنهٔ سوراخ‌کن چرم
دو سوزن سراجیدو سوزن سراجی
چکش دوشاخچکش دوشاخ
15

Fit girth straps and underskirts

Cut six stout girth straps 1 in x 1 ft 3 in; shave one end, slant the other to a fine point, edge, rub and crease double on the flesh side. Turn up the hanging web and leather until 3 in long from the tree, stitch two straps on each side and nail the third close by; punch holes along them. Drive a tough nail at the front of each skirt and clinch it. Cut two pear-shaped underskirts reaching a little over halfway down the straps, crease them with the hot creaser and nail them under the tree beneath the straps. Wrap the crupper loop in a thin hogskin strip, and fasten the flap ends to the tree with a leather chape and fine tacks.

مواد مورد نیاز این مرحله:

چرم یراقچرم یراق1 قطعه
چرم دامن زینچرم دامن زین1 قطعه
میخ زینمیخ زین2 قطعه
چرم خوکچرم خوک1 قطعه
میخمیخ1 قطعه
نخ چرمینخ چرمی1 قطعه

ابزارهای مورد نیاز:

کارد چرم‌بریکارد چرم‌بری
ابزار تاخورابزار تاخور
مشعل پروپانمشعل پروپان
منگنهٔ سوراخ‌کن چرممنگنهٔ سوراخ‌کن چرم
درفشدرفش
دو سوزن سراجیدو سوزن سراجی
چکش دوشاخچکش دوشاخ
16

Make the panel (ch. II)

Cut good basil to the saddle's underside in two halves joined along the middle, marked round the saddle with the seat awl, flush in front, to the crupper loop behind, and about 2½ in shorter at the bottom. Cut the centre slits as he describes (2 in from centre, 1½ in down, then back to about 1 in from the point) and stitch the ends. Line the top and front with basil or linen. Stitch on hogskin pockets for the tree points. Back-stitch a hogskin facing round the front and back with white linen thread, narrowing to nothing at the points and to half width at gullet and crupper loop. Tack it to white serge cut about 2½ in larger, narrowing to about 1 in at the bottom; whip the lining on and turn it out, with a rounded piece of basil or cord in the gullet.

مواد مورد نیاز این مرحله:

تیماج گوسفندی (بازیل)تیماج گوسفندی (بازیل)1 قطعه
پارچهٔ کتانپارچهٔ کتان1 قطعه
چرم خوکچرم خوک1 قطعه
سرژ پشمیسرژ پشمی1 قطعه
نخ کتاننخ کتان1 قطعه
بندبند1 قطعه

ابزارهای مورد نیاز:

کارد چرم‌بریکارد چرم‌بری
درفشدرفش
دو سوزن سراجیدو سوزن سراجی
قیچیقیچی
17

Stuff and quilt the panel

Raise stitches along the opening about 1 in apart at the back and a good 3 in in front, making two compartments. Cut a cross in the back and stuff each side pretty full with carded flock. With the seat awl work the flock down to the facing and quilt it with three-cord beeswax thread into a hard roll all round, thick at the back and front, smaller toward the front bottom; softer under the flap. Mark five or six lines about 1½ in apart across the panel flaps, and cross lines, and quilt a stitch at each crossing. Level the flock with the seat awl.

مواد مورد نیاز این مرحله:

پشم پرکنپشم پرکن1 قطعه
نخ چرمینخ چرمی1 قطعه
موم زنبور عسلموم زنبور عسل1 قطعه

ابزارهای مورد نیاز:

درفشدرفش
دو سوزن سراجیدو سوزن سراجی
کارد چرم‌بریکارد چرم‌بری
18

Fit the panel

Put the tree points into the pockets and pull them right to the end; tack the panel close to the gullet piece all round the front and two tacks between the crupper-loop points behind. Put a tuft of flock under the heads of six medium nails and drive one each side near the facing about 8 in from the crupper loop, one each side in the middle nearer the front, and one each side in front about 2 in from the top of the pockets; trim the flock at the heads.

مواد مورد نیاز این مرحله:

میخمیخ1 قطعه
پشم پرکنپشم پرکن1 قطعه

ابزارهای مورد نیاز:

چکش دوشاخچکش دوشاخ
قیچیقیچی
19

Troubleshooting

Riding saddle troubleshooting.

Flow

Loading...
20

History and honest limits

From **Saddlery**, edited by Paul N. Hasluck, David McKay, Philadelphia, 1904 (archive.org saddlery00hasl), chapters I and II. Hasluck assumes "the worker has a general acquaintance with the craft of the harness-maker" and buys the tree. All sizes are his. He lists several styles (plain flaps, demi-flap, half shafts); this is the hogskin seat and skirts with knee-pad flaps he describes in full. The metal name plate and silver dees are not made here. This is an English riding saddle, not a Western stock saddle.

مواد

19

ابزارهای لازم

18

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...