همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Screw Auger: a Steel Blade Twisted Red-Hot, with a Worm, Two Lips and an Eye for the Cross Handle (Holtzapffel, 1846)
Forge

ایجاد شده توسط

Forge

14. نوامبر 2026NO
۱۲
۰
۰
۰
۰

Screw Auger: a Steel Blade Twisted Red-Hot, with a Worm, Two Lips and an Eye for the Cross Handle (Holtzapffel, 1846)

How the common English screw auger was made, from Holtzapffel's Turning and Mechanical Manipulation: a parallel steel blade twisted red-hot, a worm at the point to pull it into the wood, two lips sharpened to cut, and the shaft end forged into an eye for a tightly driven cross handle.
پیشرفته
A day at the forge

دستورالعمل‌ها

1

Twist count

در حال بارگذاری دفترچهٔ Jupyter…
2

Read Holtzapffel

"The ordinary screw auger ... is forged as a parallel blade of steel ... it is twisted red-hot."
3

Forge the blade

Draw a steel bar out into a flat, parallel blade, leaving a round end for the shaft. Width, thickness and length are ours: make the blade as wide as the hole you want.

مواد مورد نیاز این مرحله:

میلگرد فولاد ابزارمیلگرد فولاد ابزار1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
چکشچکش
انبر آهنگریانبر آهنگری
فولر (آهن شیارزن)فولر (آهن شیارزن)
4

Twist it red-hot

Heat the blade to red, grip one end in the vice and twist the other with a wrench into an even double spiral. Twist in short heats and keep the pitch even.

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
گیرهٔ رومیزیگیرهٔ رومیزی
دسته قلاویزدسته قلاویز
انبر آهنگریانبر آهنگری
5

Form the worm and lips

File the point into a worm (a small tapered screw, as on a gimlet) that pulls the auger into the work. Shape and sharpen the two corners, or lips, to cut at the very ends and a little up the sides.

ابزارهای مورد نیاز:

گیرهٔ رومیزیگیرهٔ رومیزی
سوهان (سوهان دستی)سوهان (سوهان دستی)
6

Forge the eye

Forge the top of the shaft into a ring or eye.

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
چکشچکش
انبر آهنگریانبر آهنگری
7

Harden and temper (ours)

He gives no hardening. Ours: harden the cutting end and temper it as for other wood-cutting edge tools, then hone the lips.

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سطل آب‌دهیسطل آب‌دهی
سنگ تیزکنیسنگ تیزکنی
8

Fit the cross handle

Shape a hardwood bar and drive it tightly through the eye as a transverse handle.

مواد مورد نیاز این مرحله:

تختهٔ چوب سختتختهٔ چوب سخت1 قطعه

ابزارهای مورد نیاز:

کارد دودستهکارد دودسته
چکشچکش
9

Troubleshooting

Screw auger troubleshooting.

Flow

Loading...
10

History and honest limits

From Charles Holtzapffel, **Turning and Mechanical Manipulation**, vol. II (1846), pp. 540, 543 and 545-546 (checked on the archive.org scan turningmechanica02holtuoft). He also describes the single-lip auger: a half-round bar coiled into an open spiral with the flat side outwards, the end shaped like a shell auger. He gives no sizes or heat treatment: those, the tools and the handle wood are ours.

مواد

2

ابزارهای لازم

11

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...