همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Industrial Air Compressor: a Converted Motorcycle Engine, Motor-Driven (Shop Notes, 1919)
Emma

ایجاد شده توسط

Emma

4. نوامبر 2026SE
۹
۰
۰
۰
۰

Industrial Air Compressor: a Converted Motorcycle Engine, Motor-Driven (Shop Notes, 1919)

A workshop compressor driven by a 1 hp electric motor: an old single-cylinder motorcycle engine rebored and run as a pump, its exhaust port blanked, its own automatic inlet valve taking in air, and a ball check valve in the spark-plug hole sending air to a tank. Source: Popular Mechanics Shop Notes for 1919, pp. 3166-3167. Unknown: tank, belt and sizes. Picture: the article's drawing.
متوسط
Unknown

دستورالعمل‌ها

1

Recondition the cylinder

Rebore the old engine and fit a new piston for good compression. Remove the exhaust valve and bolt a steel plate, with a gasket under it, over the exhaust port. Leave the automatic inlet valve as it is: it now draws in air.

مواد مورد نیاز این مرحله:

ماده ناشناختهماده ناشناخته1 old motorcycle engine
مجموعهٔ پیستون و شاتونمجموعهٔ پیستون و شاتون1 new piston
ورق فولاد نرمورق فولاد نرم1 blanking plate
واشر آب‌بندیواشر آب‌بندی1 قطعه
پیچ سرشش‌گوش - ردهٔ 8.8پیچ سرشش‌گوش - ردهٔ 8.81 قطعه

ابزارهای مورد نیاز:

میلهٔ بورینگمیلهٔ بورینگ
تراش فلزتراش فلز
دریل دستیدریل دستی
آچار فرانسهآچار فرانسه
2

Fit the outlet

In place of the priming cock on top of the cylinder (the drawing shows it screwed into the spark-plug hole) fit a ball-valve hose connection, and run its hose to the air tank.

مواد مورد نیاز این مرحله:

شیر یک‌طرفهٔ ساچمه‌ایشیر یک‌طرفهٔ ساچمه‌ای1 قطعه
شلنگ بادشلنگ باد1 قطعه
ماده ناشناختهماده ناشناخته1 air tank

ابزارهای مورد نیاز:

آچار فرانسهآچار فرانسه
3

Fit the drive and mount it

Fit a longer main shaft and key an ordinary shaft pulley on its end. Leave the old flywheel in place for momentum. Bolt steel lugs to the floor and fasten the engine base to them. Belt it to a 1 hp, 110 volt motor, and put oil in the crankcase for splash lubrication.

مواد مورد نیاز این مرحله:

میلگرد فولاد نرممیلگرد فولاد نرم1 longer main shaft
قرقرهقرقره1 قطعه
ورق فولاد نرمورق فولاد نرم1 floor lugs
پیچ سرشش‌گوش - ردهٔ 8.8پیچ سرشش‌گوش - ردهٔ 8.81 قطعه
موتور برقیموتور برقی1 1 hp, 110 V
روغن ماشینروغن ماشین1 قطعه

ابزارهای مورد نیاز:

تراش فلزتراش فلز
آچار فرانسهآچار فرانسه

مواد

11

ابزارهای لازم

4

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...