همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Keyway Broaching: Tooth Pitch, Rise per Tooth, Rake and Clearance by Metal and Hardness, Pushing Force
Forge

ایجاد شده توسط

Forge

19. نوامبر 2026NO
۳
۰
۰
۰
۰

Keyway Broaching: Tooth Pitch, Rise per Tooth, Rake and Clearance by Metal and Hardness, Pushing Force

Cut a keyway in a bore with a keyway broach in an arbor press, and work out the broach criteria for your metal: tooth pitch and teeth in contact, rise per tooth and the number of teeth, rake and clearance by material and hardness, and the pushing force. Rules from Machinery's Handbook (1924), Hammond (1921), the US Navy and Metcut (1980).
متوسط
About 1 hour per part

دستورالعمل‌ها

1

How a keyway broach cuts

The broach slides through a slotted bushing in the bore. Each tooth stands a little higher than the one before (the rise), so each takes a thin chip and the keyway deepens tooth by tooth; the last teeth are the finished size and only clean up. Shims behind the broach set the depth for the next pass. Our animation; the rise is exaggerated.
مرحله 1 - Image 1
2

Tooth pitch and teeth in contact

در حال بارگذاری دفترچهٔ Jupyter…
3

Rise per tooth by metal

در حال بارگذاری دفترچهٔ Jupyter…
4

Rake and clearance by hardness

در حال بارگذاری دفترچهٔ Jupyter…
5

Pushing force (estimate)

در حال بارگذاری دفترچهٔ Jupyter…
6

Check the work hardness

Test the hub. Metcut's angles are by Brinell. For steel Hammond wants scleroscope 32-40: softer tears, harder "will rapidly destroy the broaches". He gives no Brinell or Rockwell figure; convert with a standard table (ASTM E140) if you test in Rockwell.

ابزارهای مورد نیاز:

سختی‌سنج راکولسختی‌سنج راکول
7

Bore and bushing

The bore must be to size: the broach's pilot should enter freely but not let the broach drop past the first tooth. Fit the bushing snug in the bore, slot where the keyway goes.

مواد مورد نیاز این مرحله:

قطعه خام توپی با سوراخ تراشیدهقطعه خام توپی با سوراخ تراشیده1 قطعه

ابزارهای مورد نیاز:

بوش راهنمای خان‌کش جای خاربوش راهنمای خان‌کش جای خار
کولیس ورنیهکولیس ورنیه
8

Set up in the press

Set hub, bushing and broach square under the arbor press, rigid and true. Oil the broach: broaching oil is best; lard or soluble oil will help.

ابزارهای مورد نیاز:

پرس دستیپرس دستی
خان‌کش جای خارخان‌کش جای خار
روغن برشروغن برش
9

Push it through

Push with slow, even pressure. Never bring the broach back up through the hole: push it on through and catch it on a soft cushion.

ابزارهای مورد نیاز:

پرس دستیپرس دستی
پارچهٔ پنبه‌ایپارچهٔ پنبه‌ای
10

Shim and repeat

Put the next shim behind the broach to set the next depth, oil, and push through again. Repeat until the keyway is deep enough.

ابزارهای مورد نیاز:

لایی خان‌کشلایی خان‌کش
روغن برشروغن برش
11

Measure the keyway

Check the width and the depth from the opposite side of the bore.

ابزارهای مورد نیاز:

کولیس ورنیهکولیس ورنیه
میکرومترمیکرومتر
12

Troubleshooting

Broaching problems and fixes.

Flow

Loading...
13

Sources and honest limits

*Machinery's Handbook* 6th ed. (1924) pp. 1135-1137 (first printed in Jones, *Broaching*, 1914); Hammond, *Broaching Practice* (1921) pp. 6, 7, 44; US Navy, *Machinery Repairman 3 & 2* (1990) p. 3-24; Metcut, *Machining Data Handbook* 3rd ed. (1980) Table 15.16 and pp. 17-8 to 17-20, © Metcut, cited. Not in any source we could read: cutting speed by hardness (Hammond gives 5-6 ft/min for 1921 carbon-steel broaches) and a Brinell or Rockwell limit. The force formula is our derivation. Ours: the animation, the example sizes.

مواد

1

ابزارهای لازم

9

این نقشه می‌سازد

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...