همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Lead Came: Window Rods Cast in a Split Wooden Mould (Theophilus, tr. Hendrie 1847)
Forge

ایجاد شده توسط

Forge

4. نوامبر 2026NO
۱۲
۰
۰
۰
۰

Lead Came: Window Rods Cast in a Split Wooden Mould (Theophilus, tr. Hendrie 1847)

Theophilus' way to cast window leads without an iron mould: a stick of fir is split, a groove marked with a red-dyed flax thread and cut along both halves, the halves bound with a strap and the lead poured in again and again until the hot lead has burnt the groove to the bottom. Each rod is then trimmed in a slotted wooden gauge, cut with a knife on both sides and scraped smooth. Source: Theophilus, De Diversis Artibus, Book II, ch. XXVI, tr. R. Hendrie (1847), pp. 149-151. Picture: p. 151.
متوسط
Unknown

دستورالعمل‌ها

1

Split and mark the wood

Take fir or another wood that splits smoothly, the size of the iron mould (a yard long, two fingers broad, a finger thick). Split it and round the outside. Mark each end of both pieces for the width of the rod. Stretch a thin twisted flax thread wet with red colour from mark to mark on one inner face and press the other piece against it, so the line shows on both; do the same for the second line.

ابزارهای مورد نیاز:

قالب شیار سربی شیشه‌بندقالب شیار سربی شیشه‌بند
نخ کتاننخ کتان
چاقوی کاردستیچاقوی کاردستی
2

Cut the groove

Cut the groove between the lines with a knife, as wide and deep as you wish, but not through the lower end; leave an opening at the top for pouring.

ابزارهای مورد نیاز:

چاقوی کاردستیچاقوی کاردستی
قالب شیار سربی شیشه‌بندقالب شیار سربی شیشه‌بند
3

Cast the rods

Melt the lead as for the iron mould. Bind the two halves together with a strap from top to bottom, hold the mould with a wooden holder and pour in the lead; loosen the strap and take out the rod. Bind and cast again until the burning reaches the bottom of the groove; after that you can cast gently as many as you wish.

مواد مورد نیاز این مرحله:

شمش سربشمش سرب1 pure lead

ابزارهای مورد نیاز:

قالب شیار سربی شیشه‌بندقالب شیار سربی شیشه‌بند
بند چرمیبند چرمی
دیگ سفالیدیگ سفالی
زغال چوبزغال چوب
ملاقهملاقه
4

Trim the rods

Cut a piece of wood two fingers wide and as thick as the inside of the groove, split in the middle at one end so the rod fits into the slit. With the rod in it, cut it with a knife on both sides, then smooth and scrape it as you like.

ابزارهای مورد نیاز:

چاقوی کاردستیچاقوی کاردستی

مواد

1
  • 1 pure lead
    جایگزین

ابزارهای لازم

7

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...