همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Plastic Extruder: Steam-Jacketed Screw Stuffer with a Heated Nozzle (Andersen & Strasdin, US 2,384,521, 1945)
Emma

ایجاد شده توسط

Emma

3. نوامبر 2026SE
۷
۰
۰
۰
۰

Plastic Extruder: Steam-Jacketed Screw Stuffer with a Heated Nozzle (Andersen & Strasdin, US 2,384,521, 1945)

A screw extruder for thermoplastics: a turning screw in a steam-jacketed barrel pushes hot, softened plastic forward through a short nozzle heated electrically. The barrel is kept a little below the plastic's flow temperature and the nozzle well above it, so the extruded rod comes out with a smooth, glass-like skin. Result: an extruder that makes rod, tube or strip at 25 to 30 feet a minute. Source: B. Andersen and R. F. Strasdin (Celanese), US 2,384,521 (1945). Unknown: sizes and metals. Picture: the patent drawing.
پیشرفته
Unknown

دستورالعمل‌ها

1

Make the screw

Turn a screw to fit the barrel. Its thread may be single or double; to press the plastic harder toward the nozzle, make the pitch increase or the groove get shallower toward that end. Example: a double-thread screw. Ours: mild steel. Not given: sizes.

مواد مورد نیاز این مرحله:

میلهٔ گرد فولاد نرممیلهٔ گرد فولاد نرم1 screw

ابزارهای مورد نیاز:

تراش فلزتراش فلز
دستگاه فرزدستگاه فرز
ابعاد نامعلومابعاد نامعلوم
2

Make the jacketed barrel

Make the barrel with a steam jacket round it and a steam port into the jacket, and a feed throat at the back end. The inside wall may be grooved, pitched so that every flight of the screw always meets a groove; this stops the plastic slipping. Not given: the metal, the steam pressure.

مواد مورد نیاز این مرحله:

فلز نامعلومفلز نامعلوم1 barrel and jacket

ابزارهای مورد نیاز:

تراش فلزتراش فلز
ابعاد نامعلومابعاد نامعلوم
3

Fit the heated nozzle

At the front, fit a streamlined nozzle head so no plastic can pocket and decompose, and a nozzle 1/2 to 18 inches long; about 6 inches in the example. Perforated plates may go between the screw and the nozzle. Heat the nozzle with an electric resistance coil. Ours: nichrome wire.

مواد مورد نیاز این مرحله:

فلز نامعلومفلز نامعلوم1 nozzle head and nozzle
سیم نیکرومسیم نیکروم1 nozzle heating coil
مادهٔ عایق نامعلوممادهٔ عایق نامعلوم1 coil insulation

ابزارهای مورد نیاز:

تراش فلزتراش فلز
4

Drive the screw

Drive the screw through a gear from a motor, so its speed can be kept steady; 20 revolutions a minute in the example. Not given: the drive.

مواد مورد نیاز این مرحله:

موتور برقیموتور برقی1 drive motor
فلز نامعلومفلز نامعلوم1 drive gears

ابزارهای مورد نیاز:

ابعاد نامعلومابعاد نامعلوم
5

Extrude a rod

Keep the barrel 0 to 100 °F below the plastic's flow temperature and the nozzle 50 to 100 °F above it. Example: barrel at about 270 °F by steam, nozzle at about 400 °F, for a cellulose acetate with a flow temperature of 307 °F. Feed the hot, softened plastic into the throat at a steady rate. Carry the rod away on a conveyor and cool it at once with cold water, then cut it to length.

ابزارهای مورد نیاز:

دیگ بخاردیگ بخار
پیرومترپیرومتر
آبآب

مواد

5

ابزارهای لازم

6
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...