هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Push Button: Normally Open Momentary Switch with a Cushioned Contact (De Reamer, GE 1939)
Ed

ایجاد شده توسط

Ed

28. اکتبر 2026FI
۱
۰
۰
۰
۰

Push Button: Normally Open Momentary Switch with a Cushioned Contact (De Reamer, GE 1939)

A panel push button that closes a circuit only while you press it. A spring holds the button out, and a metal rim on the end of its rod sits clear of two contacts. Press it and the rim bridges both contacts. A second spring inside the button lets the rod give, so the contacts never take more than that spring's force. Source: Frank C. De Reamer, US 2,166,803 (General Electric, 1939), Fig. 5. Unknown: the insulating material, the metals and every size. De Reamer gives none of them, so they are linked to unknown heads. The tools are ours. Picture: the patent's Fig. 5.
پیشرفته
2 days

دستورالعمل‌ها

1

Mould the housing

Mould a cup-shaped housing of insulating material, with a boss on each of two opposite sides, a recess in the top of each boss, a groove inside below each boss, and a bead round the top. Unknown: the material, the sizes and the moulding.

مواد مورد نیاز این مرحله:

مادهٔ عایق نامعلوممادهٔ عایق نامعلوم1 as required

ابزارهای مورد نیاز:

قالب فشاریقالب فشاری
ابعاد نامعلومابعاد نامعلوم
2

Make the terminals and contacts

Bend two angled metal strips. The upper end of each sits in a boss recess, and the lower end is a solder lug. Fix each upper end to a contact that fits the groove inside the housing, stepped at its bottom end. Unknown: the metal.

مواد مورد نیاز این مرحله:

فلز نامعلومفلز نامعلوم1 as required

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
انبردست تختانبردست تخت
ابعاد نامعلومابعاد نامعلوم
3

Make the sleeve, plate and cover

Turn a threaded sleeve and cut its thread. Spin its lower end over onto a metal plate with tangs. Cut a cover of insulating sheet with ears that reach over the bosses and a hole in the middle to guide the rod.

مواد مورد نیاز این مرحله:

فلز نامعلومفلز نامعلوم1 as required
مادهٔ عایق نامعلوممادهٔ عایق نامعلوم1 as required

ابزارهای مورد نیاز:

تراش فلزتراش فلز
ست ابزار تراش (HSS)ست ابزار تراش (HSS)
دسته حدیدهدسته حدیده
قیچی ورق‌بریقیچی ورق‌بری
کولیس ورنیهکولیس ورنیه
ابعاد نامعلومابعاد نامعلوم
4

Make the push button

Make a drawn metal tube closed at the top, and a rod with a head. Put a small coil spring in the top of the tube, then the rod's head. Wedge a washer into the tube under the head. Leave clearance so the rod can swivel a little. Turn the rod's lower end down to a smaller diameter. Unknown: the metal.

مواد مورد نیاز این مرحله:

فلز نامعلومفلز نامعلوم1 as required
مجموعه فنر فشاریمجموعه فنر فشاری1 spring

ابزارهای مورد نیاز:

تراش فلزتراش فلز
ست ابزار تراش (HSS)ست ابزار تراش (HSS)
کولیس ورنیهکولیس ورنیه
ابعاد نامعلومابعاد نامعلوم
5

Assemble

Set the terminals in their recesses and the contacts in their grooves. Slide the button into the sleeve, with a coil spring round the rod between the cover and the wedged washer. Pass the rod's end through the cover's hole. Put on it a loose insulating washer with a metal rim round its edge. Hammer the rod's end over into a flange. Lay the cover on the housing, so its ears clamp the terminals, and bend the plate's tangs over the bead.

مواد مورد نیاز این مرحله:

مادهٔ عایق نامعلوممادهٔ عایق نامعلوم1 as required
فلز نامعلومفلز نامعلوم1 as required
مجموعه فنر فشاریمجموعه فنر فشاری1 spring

ابزارهای مورد نیاز:

گیرهٔ رومیزیگیرهٔ رومیزی
چکش گِرد‌سرچکش گِرد‌سر
انبردست تختانبردست تخت
عینک ایمنیعینک ایمنی
6

Mount and wire it

Put the sleeve through a hole in the panel and clamp the panel between two nuts on the thread. Solder the bared wire ends to the two lugs.

مواد مورد نیاز این مرحله:

مهرهٔ شش‌گوشمهرهٔ شش‌گوش2 pcs
سیم لحیمسیم لحیم1 as required

ابزارهای مورد نیاز:

هویههویه
انبردست تختانبردست تخت
7

Check it

At rest, the rim sits against the underside of the cover and the circuit is open. Pressed, the rim meets the stepped ends of both contacts and closes it. The checking is ours: the meter reads open, then closed while pressed.

ابزارهای مورد نیاز:

مولتی‌مترمولتی‌متر

مواد

5

ابزارهای لازم

13

این نقشه می‌سازد

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...