همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Rip Saw: a Hand Saw Filed with Upright Teeth and Little Set (Cassell's Cyclopaedia, 1904)
Woody

ایجاد شده توسط

Woody

5. نوامبر 2026NO
۱۷
۰
۰
۰
۰

Rip Saw: a Hand Saw Filed with Upright Teeth and Little Set (Cassell's Cyclopaedia, 1904)

A rip saw cuts along the grain, so its teeth work like a row of small chisels, not like the knife points of a cross-cut saw. Cassell's Cyclopaedia of Mechanics (1904) says how to file one: the fronts of the teeth perfectly upright, the faces given a transverse bevel of only 3 to 5 degrees (the file held at 85 and 95 degrees), and only a little set, less than a cross-cut saw needs. It gives no tooth size, back angle or amount of set; those are unknown here. Source: P. N. Hasluck (ed.), Cassell's Cyclopaedia of Mechanics vol. V (1904), p. 73, Setting Saw Teeth. Picture: our diagram.
متوسط
An hour

دستورالعمل‌ها

1

Read Cassell's

"The teeth in a rip saw should be so filed that their fronts will be perfectly upright. A transverse bevel of from 3° to 5° should be given to the faces of the teeth."
2

Clamp the saw

Clamp the hand saw in the vice with its teeth just above the jaws, so the blade cannot chatter under the file.

مواد مورد نیاز این مرحله:

ارّهٔ نجاریارّهٔ نجاری1 hand saw

ابزارهای مورد نیاز:

گیرهٔ رومیزیگیرهٔ رومیزی
3

File the teeth upright

File each tooth so its front stands perfectly upright to the line of the teeth. Hold the file at 85° to the blade for one side and 95° for the other, to give the faces a transverse bevel of about 5°; 3° is the least. File alternate teeth from one side, then turn the saw and file the others. Tooth size and the slope of the backs are not given (unknown).

ابزارهای مورد نیاز:

سوهان دندانه ارهسوهان دندانه اره
ابعاد نامعلومابعاد نامعلوم
4

Set lightly and evenly

Set the teeth alternately left and right with the saw set, the same amount on each side. A properly ground ripping saw needs only a little set, less than a cross-cut saw; how much depends on the timber, the thickness of the blade and how it is ground (not given, unknown).

ابزارهای مورد نیاز:

انبر دندانه‌خم‌کن ارهانبر دندانه‌خم‌کن اره
ابعاد نامعلومابعاد نامعلوم
5

History and honest limits

On the same page Cassell's gives the other hand saws: a cross-cut saw's fronts recline about 10° and need a keener edge, a tenon saw is filed much like a hand saw with less bevel, and a panel saw, used both ripping and cross-cutting, like a mitre saw. Tooth size, back angle and amount of set are not given; the saw is a hand saw refiled for ripping.

مواد

1

ابزارهای لازم

4

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...