همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Bulb Pipette Blown at the Lamp: a Closed Tube Drawn, Bulbed, Pierced and Joined to Two Stems (Soward, 1886)
Bubbles

ایجاد شده توسط

Bubbles

14. نوامبر 2026IT
۶
۰
۰
۰
۰

Bulb Pipette Blown at the Lamp: a Closed Tube Drawn, Bulbed, Pierced and Joined to Two Stems (Soward, 1886)

Alfred Soward's lampwork bulb pipette from Amateur Work (1886), made like his thistle funnel: a 3/8 in. bore tube closed and drawn down onto a 1/8 in. stem, blown into a bulb, a thin second bulb blown and broken off the far side to leave a short neck, and a second stem drawn to a fine capillary tip joined on.
پیشرفته
An hour once the basic operations are mastered

دستورالعمل‌ها

1

Read Soward

"To make a pipette the process is very similar." (to the thistle funnel)
2

Prepare the tubes

Take glass tube of about 1/8 in. (3 mm) bore for the stems and about 3/8 in. (10 mm) bore for the bulb. Close the wide tube at one end in the form of his fig. 41 A, then soften it about an inch from the end and draw it down to the small tube's diameter.

مواد مورد نیاز این مرحله:

لوله شیشه‌ایلوله شیشه‌ای1 قطعه

ابزارهای مورد نیاز:

چراغ بونزنچراغ بونزن
دم شیشه‌گریدم شیشه‌گری
3

Join the first stem

Cut the drawn, flask-shaped piece off with a file and fuse it to a length of the narrow tube: soften both ends, press them together, pull gently to reduce the thickened joint, and blow a gentle stream of air in.

مواد مورد نیاز این مرحله:

لوله شیشه‌ایلوله شیشه‌ای1 قطعه

ابزارهای مورد نیاز:

سوهان (سوهان دستی)سوهان (سوهان دستی)
چراغ بونزنچراغ بونزن
دم شیشه‌گریدم شیشه‌گری
4

Blow the bulb

Soften the flask part and blow it into a bulb through the stem.

ابزارهای مورد نیاز:

چراغ بونزنچراغ بونزن
دم شیشه‌گریدم شیشه‌گری
5

Open the far end

Play the flame on the point opposite the stem (A in fig. 41) and blow a very thin second bulb with a strong blast. Break it away: it leaves a small projecting tube (B).

ابزارهای مورد نیاز:

چراغ بونزنچراغ بونزن
دم شیشه‌گریدم شیشه‌گری
6

Draw and join the tip

Draw a second piece of narrow tube to a capillary end: thicken it in the flame, pull the hands apart, cut with a file and hold the cut end a moment in the flame. Join this stem to the projecting tube as before.

مواد مورد نیاز این مرحله:

لوله شیشه‌ایلوله شیشه‌ای1 قطعه

ابزارهای مورد نیاز:

سوهان (سوهان دستی)سوهان (سوهان دستی)
چراغ بونزنچراغ بونزن
دم شیشه‌گریدم شیشه‌گری
7

Troubleshooting

Pipette troubleshooting.

Flow

Loading...
8

History and honest limits

From Alfred W. Soward, "Glass-Blowing for Amateurs" IV, **Amateur Work, Illustrated**, vol. V (1886), pp. 173-176, figs. 39-41 (checked on the archive.org scan amateurworkillus05lond). He gives no volume or graduation: calibrate it by weighing water if you need one (see the graduated-pipette blueprint). Metric figures are ours.

مواد

1

ابزارهای لازم

3

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...