همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)
Woody

ایجاد شده توسط

Woody

13. نوامبر 2026NO
۱۰
۰
۰
۰
۰

16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)

Stillman Taylor's open Canadian canoe from The Boy Mechanic, Book 3 (1919): about 16 ft long, 31 in beam, 60 to 70 lb. Built upside down over a backbone and seven paper-pattern molds, with oak or ash stems, keelson and gunwales, 1/8 in cedar ribs and planking fastened with copper clout nails, then covered with No. 6 canvas laid in melted marine glue, painted, and varnished. Every layout dot and width is his, as printed.
پیشرفته
Several weeks

دستورالعمل‌ها

1

His layout data

در حال بارگذاری دفترچهٔ Jupyter…
2

Read The Boy Mechanic, Book 3

"Working with light materials, the canoe builder must pay particular attention to the workmanship ... the work must not be hurried, but plenty of time taken to do each and every part well."
3

Get the materials

Stem: oak or ash 6 ft x 3/4 in square. Keelson: oak or ash 14 ft x 3-1/2 x 3/8 in. Gunwales: 2 of oak or ash 16 ft x 7/8 x 1/2 in. Seat risings: 2 of oak or ash 1/2 in square. Fenderwales: 34 ft of 1/2 in half-round molding. Outside keel (optional): oak 14 ft x 1 x 1/2 in. Deck beams: 2 of oak or ash 8 x 1-1/8 x 3/8 in. Seat frames: 2 at 30 x 3 x 3/4 and 2 at 12 x 2-1/4 x 3/4 in. Planking: cedar or pine, 100 sq ft, 1/8 in (25 ft of 1 in lumber dressed to 1/8 in, in 12, 14 and 16 ft lengths). Ribs: 360 running ft of cedar 1-3/4 x 1/8 in. Breast hooks: cedar or oak 32 x 9 x 3/4 in. Backbone, molds and ribbands from any cheap stuff. Fastenings: 1 lb 2 in wire nails; 1 lb 5/8 in and 1/2 lb 3/4 in copper clout nails; 18 brass screws 1-1/4 in No. 8 and 24 brass screws 1 in No. 6; 4 lb marine glue; 3 oz No. 2 copper tacks; 11-3/4 yd No. 6 canvas; 1 lb 3/8 in copper tacks. Rock elm or fir may replace oak or ash; spruce, pine, cypress or fir may replace cedar.

مواد مورد نیاز این مرحله:

تختهٔ بلوط سفیدتختهٔ بلوط سفید4 قطعه
تختهٔ سرو قرمزتختهٔ سرو قرمز6 قطعه
تختهٔ کاجتختهٔ کاج3 قطعه

ابزارهای مورد نیاز:

اره طولی‌براره طولی‌بر
ارهٔ دستیارهٔ دستی
رندهٔ دستیرندهٔ دستی
متر نواریمتر نواری
4

Lay out the backbone and molds

Cut the backbone from a 16 ft x 4 x 7/8 in board, top edge 15 ft 8-3/4 in, and mark the mold stations from each end: 22-1/4 in to mold 1, then 23-1/4 in to mold 2 and 23-1/4 in to mold 3, each mold space 3/4 in thick; mold 4 sits at the centre; cut the ends off on the bevel (Fig. 1). Draw each mold on stiff paper from his rectangles, mortises and dots (notebook), trace the curve through the dots, cut out the half, fold and draw the other side, and cut the molds from 7/8 in stock: seven in all, numbered alike from each end: two No. 1, two No. 2 (each in halves), two No. 3 and one No. 4; nail battens across the halves.

مواد مورد نیاز این مرحله:

تختهٔ کاجتختهٔ کاج2 قطعه
ورق‌های کاغذ ضخیمورق‌های کاغذ ضخیم1 قطعه
میخمیخ1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
ارهٔ موییارهٔ مویی
خط‌کشخط‌کش
مدادمداد
قیچیقیچی
چکشچکش
5

Bend the stems and shape the keelson

Make the stem mold from his Fig. 6 pattern (24-1/2 x 12 in rectangle, dots in the notebook) and bend the straight-grained 3/4 in square oak or ash stems on it. Cut the keelson 13 ft 11 in long, tapering from 3-1/2 in at the centre: 3-1/2 in at 1 and 2 ft, 3-1/4, 2-5/8, 2 and 1-1/4 in at 3 to 6 ft, and 15/16 in at the ends (Fig. 7). Fasten each stem to the keelson with a couple of 3/4 in No. 10 screws.

مواد مورد نیاز این مرحله:

تختهٔ بلوط سفیدتختهٔ بلوط سفید2 قطعه
پیچ چوب برنجیپیچ چوب برنجی4 قطعه

ابزارهای مورد نیاز:

کارد دودستهکارد دودسته
رندهٔ دستیرندهٔ دستی
ارهٔ دستیارهٔ دستی
دریل دستهٔ گردان با متهدریل دستهٔ گردان با مته
پیچ‌گوشتی تختپیچ‌گوشتی تخت
گیرهٔ سی‌شکلگیرهٔ سی‌شکل
6

Set up the frame

Build it upside down: set the backbone on boxes about 1 ft or more off the floor and the molds in their numbered places, the backbone resting in their top mortises. True the molds with a square and toenail them. Lay the keelson in its mortises, fit the stems to the backbone angle and nail through the mold tops into them. Bevel the stem splice from the inside, leaving the outer edge about 1/8 in wide. Put on the gunwales at the sheer line with nails left proud, then four ribbands a side at 5 in centres from the keel, fastened with 1-1/4 in brads.

مواد مورد نیاز این مرحله:

تختهٔ بلوط سفیدتختهٔ بلوط سفید2 قطعه
تختهٔ کاجتختهٔ کاج1 قطعه
میخمیخ1 قطعه

ابزارهای مورد نیاز:

گونیای ثابتگونیای ثابت
چکشچکش
اسکنه‌هااسکنه‌ها
رندهٔ دستیرندهٔ دستی
7

Rib the hull

Saw cedar ribs 1-3/4 in wide and 1/8 in thick, cut to length gunwale to gunwale over the ribbands. Space them 3 in apart on centres along the keelson, one over each mold. Fasten each rib to the outside of the keelson with two 5/8 in copper clout nails, spring it in under the ribbands and fasten it to the gunwales. Then remove the ribbands.

مواد مورد نیاز این مرحله:

تختهٔ سرو قرمزتختهٔ سرو قرمز2 قطعه
میخ مسی سرپهنمیخ مسی سرپهن1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
چکشچکش
متر نواریمتر نواری
8

Plank the hull

Plank with 1/8 in cedar, bent cold, full length stem to stem, butted edge to edge without bevel, about 3 in wide; begin with the garboard strake at the keel and end with the sheer strake level with the gunwale. Punch nail holes with an awl, staggered along the ribs; clamp the plank, drive copper clout nails and clinch them inside on a clinch iron. Trim the plank ends to the stems and gunwales, saw the backbone in two to take out the frame, tack strips across the gunwales against sagging, and nail where the molds were.

مواد مورد نیاز این مرحله:

تختهٔ سرو قرمزتختهٔ سرو قرمز4 قطعه
میخ مسی سرپهنمیخ مسی سرپهن1 قطعه
پونز مسیپونز مسی1 قطعه

ابزارهای مورد نیاز:

درفشدرفش
گیرهٔ سی‌شکلگیرهٔ سی‌شکل
آهن پشت‌بند پرچآهن پشت‌بند پرچ
چکشچکش
ارهٔ دستیارهٔ دستی
9

Fit risings, seats, decks and thwarts

Nail 1/2 in square oak or ash seat risings, 14 ft long, about 4 in below the gunwale, boring first and clinching inside. Make the seat frames as Fig. 10 and cane them or tack on canvas (a kneeling paddler may use a 4 or 5 in seat bar instead). Notch the 8 x 1-1/8 x 3/8 in deck beams to wedge about 1/2 in against the gunwales (Fig. 11) and fix each with a 1-1/4 in No. 10 screw through the gunwale. Shape the decks 16 x 8 in (Fig. 12) and fix them with three 1-1/4 in No. 10 screws into the beam and three along each gunwale. Screw a centre thwart of oak or ash, 3/8 in thick, 2 in tapering to 1 in, under the gunwales amidships; extra thwarts behind the forward seat and about 3 ft forward of the rear seat stiffen it.

مواد مورد نیاز این مرحله:

تختهٔ بلوط سفیدتختهٔ بلوط سفید2 قطعه
تختهٔ سرو قرمزتختهٔ سرو قرمز1 قطعه
میخ مسی سرپهنمیخ مسی سرپهن1 قطعه
پیچ چوب برنجیپیچ چوب برنجی30 قطعه
پارچهٔ کرباسپارچهٔ کرباس1 قطعه

ابزارهای مورد نیاز:

دریل دستهٔ گردان با متهدریل دستهٔ گردان با مته
پیچ‌گوشتی تختپیچ‌گوشتی تخت
ارهٔ دستیارهٔ دستی
اسکنه‌هااسکنه‌ها
چکشچکش
10

Lay the canvas

Lay the No. 6 canvas smoothly on the hull and trim it to fold at the stems (Fig. 13). Melt the black marine glue in a can over a moderately hot fire and spread a fairly heavy coat over one side of the canvas with a stiff brush. Lay it on and iron it with a moderately hot flatiron so the glue melts into the planking. Tack the edges along the gunwales and fold the canvas smoothly at the stems, tacking exactly down the stem centre line.

مواد مورد نیاز این مرحله:

پارچهٔ کرباسپارچهٔ کرباس1 قطعه
چسب دریاییچسب دریایی1 قطعه
پونز مسیپونز مسی1 قطعه

ابزارهای مورد نیاز:

قوطی حلبیقوطی حلبی
قلم‌موی پهنقلم‌موی پهن
اتوی آهنیاتوی آهنی
قیچیقیچی
چکشچکش
11

Fenders, stem bands and keel

Tack 1/2 in round molding over the canvas edge (or a 1 in strip of planking with 1-1/4 in brads every 2 or 3 in). Put on stem bands of wood about 3/8 in square, rounded, with 1-1/4 in brads, or better, 3/8 in brass oval stem band with 3/4 in screws. An outside keel is optional: about 1 x 1/2 in of oak or ash tapered to the stem bands, or a flat keel about 2-1/2 in wide of 3/8 in oak or ash, which turns more easily and guards the bottom.

مواد مورد نیاز این مرحله:

ابزار چوبی نیم‌گردابزار چوبی نیم‌گرد1 قطعه
نوار برنجی دماغهٔ قایقنوار برنجی دماغهٔ قایق2 قطعه
پیچ چوب برنجیپیچ چوب برنجی12 قطعه
تختهٔ بلوط سفیدتختهٔ بلوط سفید1 قطعه
میخمیخ1 قطعه

ابزارهای مورد نیاز:

چکشچکش
پیچ‌گوشتی تختپیچ‌گوشتی تخت
رندهٔ دستیرندهٔ دستی
دریل دستیدریل دستی
12

Paint and finish

Give the canvas a coat of shellac to waterproof it, then four coats of paint to fill the fibres, rubbing down the second and third with fine sandpaper. Finish all woodwork with three coats of good outside spar varnish. A removable slatted grating of soft-pine lattice, about 1-1/8 in wide and 1-1/4 in thick as printed, screwed to curved cross strips (not the ribs), protects the bottom.

مواد مورد نیاز این مرحله:

ورنی شلاکیورنی شلاکی1 قطعه
رنگ روغنرنگ روغن1 قطعه
کاغذ سنبادهکاغذ سنباده1 قطعه
ورنی دکلورنی دکل1 قطعه
تختهٔ کاجتختهٔ کاج1 قطعه

ابزارهای مورد نیاز:

قلم‌موی پهنقلم‌موی پهن
پیچ‌گوشتی تختپیچ‌گوشتی تخت
13

Troubleshooting

Canoe troubleshooting.

Flow

Loading...
14

History and honest limits

From "How to Build a Canoe, Part I" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 77-84). As printed, his text differs in places: the backbone's lower edge is 1/2 in longer in one sentence and 1 in in the next; the list gives No. 8 deck screws, the text No. 10; the list's seat frames (30 x 3 and 12 x 2-1/4 in) differ from Fig. 10 (29 x 9 in); the fenders are half-round in the list and round in the text. The metric figures are ours.

مواد

16

ابزارهای لازم

21

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...