همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Skis: Ash or Hickory Planks Shaped to an 8 ft Pattern, Steam-Bent Tips and a Running Groove (Boy Mechanic, 1919)
Woody

ایجاد شده توسط

Woody

13. نوامبر 2026NO
۶
۰
۰
۰
۰

Skis: Ash or Hickory Planks Shaped to an 8 ft Pattern, Steam-Bent Tips and a Running Groove (Boy Mechanic, 1919)

Stillman Taylor's skis from The Boy Mechanic, Book 3 (1919): "far easier than snowshoe construction, since each runner is made from a single piece of plank". Ash or hickory is cut to his 8 ft pattern, thinned from the top only, the tips steamed to a 6 in bend, a centre groove cut, and the skis oiled and waxed.
متوسط
About 1 week

دستورالعمل‌ها

1

Fig. 5 in centimetres, and the wax

در حال بارگذاری دفترچهٔ Jupyter…
2

Read The Boy Mechanic, Book 3

"Either hickory or ash will give satisfaction, because both are heavy woods, as well as strong and flexible." For a man of good height, 7 to 8 ft is the right length.
3

Get and choose the wood

Get two ash or hickory planks about 9 ft long and 2 in thick, from the outside of the lower trunk, with the grain running as in his Fig. 6, A/D (in ash choose open, widely spaced grain). Or split a sound, straight tree about 10 in across and clear of knots for 10 ft: axe a straight groove about 1 in deep along each side and drive small wood wedges along it; hew only enough off the outside to make the flat running surface.

مواد مورد نیاز این مرحله:

تختهٔ چوب سختتختهٔ چوب سخت2 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
متر نواریمتر نواری
4

Lay out and saw

Make a paper pattern from his Fig. 5 (8 ft ski): 3-3/8 in wide at the heel, 3-1/8 in at the foot, 4 in at the bend, rounding to the toe. Trace it on the plank and saw out; on green wood make the width about 1/4 in greater for shrinkage.

مواد مورد نیاز این مرحله:

تختهٔ چوب سختتختهٔ چوب سخت1 قطعه

ابزارهای مورد نیاز:

مدادمداد
ارهٔ دستیارهٔ دستی
متر نواریمتر نواری
5

Plane to thickness

Plane the running surface perfectly smooth, grain straight from point to heel. Work the thickness down from the top side only, never the bottom: about 1/2 in at the heel, 3/4 in at the foot and 1/2 in at the bend.

ابزارهای مورد نیاز:

رندهٔ دستیرندهٔ دستی
رندهٔ دودستهرندهٔ دودسته
6

Steam the tip

Lay the ski over a wash boiler of boiling water and soak the tip by mopping it with the water on a cloth tied to a stick. Bend gradually over many treatments to a good 6 in bend (it finishes near 5 in, as the wood straightens a little as it dries). Hold it in a rough frame over a short log, or lash or cleat the tips to the bench, as in his Fig. 7. The arch under the foot is easily put in, and easily straightened when cold if overdone.

ابزارهای مورد نیاز:

دیگ بزرگدیگ بزرگ
تیتی
گیرهٔ میله‌ایگیرهٔ میله‌ای
7

Binding hole, balance and groove

Put in the hole for the foot binding. If the wood was left long, trim the heel so the ski balances when lifted by the toe straps (he sees no advantage in weighting a light heel with lead). Cut a groove in the exact centre of the running surface, about 1/8 in deep and 3/8 to 1/2 in wide, from the heel to the start of the bend, with a grooving plane or a small gouge.

مواد مورد نیاز این مرحله:

بند چرمیبند چرمی2 قطعه

ابزارهای مورد نیاز:

دریل دستیدریل دستی
اسکنه‌هااسکنه‌ها
اسکنه ناودانیاسکنه ناودانی
ارهٔ دستیارهٔ دستی
8

Finish and wax

Sandpaper top and bottom and rub down with linseed oil with a little paraffin or beeswax in it; oil and wax the running surface (spar varnish on the tops if you want gloss). For a hard wax, melt 10 oz of beeswax with 5 oz of rosin, stir in 1 oz of turpentine and pour into small boxes. Rub it on and go over it with a hot flatiron; too much wax makes climbing hard.

مواد مورد نیاز این مرحله:

کاغذ سنبادهکاغذ سنباده1 قطعه
روغن بزرکروغن بزرک1 قطعه
موم پارافینموم پارافین1 قطعه
موم زنبور عسلموم زنبور عسل1 قطعه
کلوفن کاجکلوفن کاج1 قطعه
تربانتینتربانتین1 قطعه

ابزارهای مورد نیاز:

دیگ بزرگدیگ بزرگ
اتوی آهنیاتوی آهنی
قلم‌موی پهنقلم‌موی پهن
9

Troubleshooting

Ski troubleshooting.

Flow

Loading...
10

History and honest limits

From "How to Make Skis" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 27-30). His text gives the groove as 3/8 to 1/2 in wide; Fig. 5 shows 3/8 in. He does not describe the binding. The tools and metric figures are ours.

مواد

8
  • جایگزین
  • 2 قطعه
    جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین

ابزارهای لازم

13
  • جایگزین
  • 1 vendor sell this, none ship to you yet
    جایگزین
  • 1 vendor sell this, none ship to you yet
    جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...