همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Cross-Hole Countersinks: A Slanting Hole Through the Cone Makes One Spiral Shearing Lip (Taylor, 1903)
Forge

ایجاد شده توسط

Forge

13. نوامبر 2026NO
۱۰
۰
۰
۰
۰

Cross-Hole Countersinks: A Slanting Hole Through the Cone Makes One Spiral Shearing Lip (Taylor, 1903)

John M. Taylor of Hartford, Connecticut, received US 724,520, dated 7 April 1903, for a countersink that shears wood smoothly. Its conical head has a hole drilled through it at a slant that crosses the axis and reaches the point. One edge of that hole is the cutting lip, a spiral curve from the point out to the rim, and the chips go straight out through the hole to the back. A short band behind the cone guides it. We turn a set of three from tool steel and harden them. The patent gives no sizes; every size here is ours.
متوسط
About 1 day

دستورالعمل‌ها

1

Where the slanting hole must go

در حال بارگذاری دفترچهٔ Jupyter…
2

Read US 724,520

"One of the outer edges of the wall of the opening forms a cutting-lip 8, which is of spiral formation, whereby it is effective to make a shear cut, and terminates in a shoulder 9, forming an entering or cutting point 4 at the apex of the conical head 2."
3

Turn the blanks

From octagonal tool steel big enough for each head, turn three blanks: a 90 degree cone 2 to a sharp point, 12, 16 and 20 mm across at its base; a band 5 2 mm long at that diameter as the guide; a truncated cone 6 down to an 8 mm shank 50 mm long. File three flats on each shank's end for the chuck. Heat each to a cherry red and let it cool slowly in the air, to soften it for drilling.

مواد مورد نیاز این مرحله:

میلهٔ هشت‌گوش فولاد ابزارمیلهٔ هشت‌گوش فولاد ابزار2 قطعه

ابزارهای مورد نیاز:

تراش فلزتراش فلز
سه‌نظام تراشسه‌نظام تراش
رندهٔ تراشکاریرندهٔ تراشکاری
رندهٔ برش تراشرندهٔ برش تراش
نقالهنقاله
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
مجموعه سوهانمجموعه سوهان
کورهٔ آهنگریکورهٔ آهنگری
انبر آهنگریانبر آهنگری
عینک ایمنیعینک ایمنی
4

Drill the slanting opening 7

Hold a blank in the machine vice tilted so the drill meets the cone's side at 35 degrees to the tool's axis, aimed to cross the axis just behind the point (the notebook gives how far). Drill through with a drill 0.45 of the head across: 5.5, 7 and 9 mm, so the hole breaks out through the point on one side and out of the back cone on the other. Open the back of the hole a little larger, so it tapers towards the shank.

ابزارهای مورد نیاز:

دریل ستونیدریل ستونی
گیرهٔ ماشینگیرهٔ ماشین
نقالهنقاله
مجموعه متهمجموعه مته
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
5

File the lip 8

With a round needle file, clean the hole's edge on the side that leads as the countersink turns, leaving it sharp from the point to the band: that is the spiral cutting lip. File a little relief on the cone just behind it, and leave the shoulder 9 at the point.

ابزارهای مورد نیاز:

مجموعه سوهان سوزنیمجموعه سوهان سوزنی
گیرهٔ ماشینگیرهٔ ماشین
سنگ‌سنبادهٔ رومیزیسنگ‌سنبادهٔ رومیزی
6

Harden and temper

Heat each head to a cherry red, until a magnet no longer sticks, and quench it point first in water, moving it about. Rub it bright with a stone, heat the shank gently 20 mm behind the head, and quench again as soon as a light straw colour reaches the cutting lip.

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
انبر آهنگریانبر آهنگری
آهن‌ربای کوچکآهن‌ربای کوچک
سطل آب‌دهیسطل آب‌دهی
آبآب
سنگ تیزکنیسنگ تیزکنی
دستکش جوشکاریدستکش جوشکاری
عینک ایمنیعینک ایمنی
7

Hone and test

Hone the lip lightly with the stone. Drill a few screw holes in hardwood and countersink them in the drill: the cone should cut a smooth bell without chatter and the chips should come out of the hole at the back.

ابزارهای مورد نیاز:

سنگ تیزکنیسنگ تیزکنی
دریل شارژیدریل شارژی
مجموعه متهمجموعه مته
تختهٔ چوب سختتختهٔ چوب سخت
عینک ایمنیعینک ایمنی
8

Troubleshooting

Countersink troubleshooting.

Flow

Loading...
9

History and honest limits

**John M. Taylor** of Hartford, Connecticut, US 724,520, dated 7 April 1903, filed 7 November 1901. He claimed "a countersink having a cone-shaped head provided with an opening crossing diagonally to the axis within the length of the tool and intersecting the apex of the cone, said opening having a curved edge forming a cutting-lip", and a two-part shank for brace or chuck. We make one-piece shanks for a chuck. He gives no sizes, angle or steel; our 90 degree cones, sizes and the house hardening are ours.

مواد

1

ابزارهای لازم

22

این نقشه می‌سازد

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...