هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
The Button Corkscrew: A Helix That Grips and a Disc That Stops It
Youblob (drawn diagram, draw_corkscrew.py) · CC0
YourGrandma

ایجاد شده توسط

YourGrandma

27. سپتامبر 2026IS
۷
۰
۰
۰
۰

The Button Corkscrew: A Helix That Grips and a Disc That Stops It

A cork is squeezed into a bottle neck so hard that pulling it out by a simple worm takes a strong arm — and a worm driven too far pierces the cork and pushes crumbs into the wine. Samuel Henshall, an English clergyman, took out British patent No. 2061 on 24 August 1795 for a corkscrew with a button: a concave disc fixed between the worm and the shank. The button stops the worm once it is deep enough, and turning on past that point twists the whole cork in the neck, breaking its hold on the glass before it is pulled. Matthew Boulton's works in Birmingham made it. This rung works out the worm's turns and grip and the force a pull needs, and makes and tests a button corkscrew.
مبتدی
About 2 hours

دستورالعمل‌ها

1

Worm pitch, grip and pulling force

در حال بارگذاری دفترچهٔ Jupyter…
2

The helix underneath it

A corkscrew worm is a helix with nothing inside it. The embedded blueprint shows the helix as a ramp wrapped round a cylinder.
3

Make a worm and a button

Wind 2 mm spring steel wire round a 6 mm rod held in a vice, five turns at an 8 mm pitch — set the pitch by winding over a spacer strip. Grind the free end to a point on the outside of the helix so it follows the helix, not the centre. Leave a straight tail as the shank. For the button, drill a 20 mm steel washer to fit the shank and file its underside slightly concave with abrasive paper wrapped round a rod. Slide it down to where the worm starts and solder it in place. Fit a wooden handle across the top of the shank.

مواد مورد نیاز این مرحله:

سیم فولاد فنرسیم فولاد فنر1 قطعه
واشر تختواشر تخت1 قطعه
میخ‌های چوب سختمیخ‌های چوب سخت1 قطعه
لحیم قلع-سربلحیم قلع-سرب1 قطعه

ابزارهای مورد نیاز:

گیرهٔ رومیزیگیرهٔ رومیزی
دریل شارژیدریل شارژی
مجموعه متهمجموعه مته
مجموعه کاغذ سنبادهمجموعه کاغذ سنباده
هویههویه
دستکش کار چرمیدستکش کار چرمی
عینک ایمنی شفافعینک ایمنی شفاف
4

Measure the pull, with and without the twist

Recork several empty wine bottles with new corks of the same kind, using a hand corker, and let them stand a day. On the first, drive the worm in until the button touches, stop, and pull straight up with a spring scale hooked to the handle: read the peak force. On the next, drive it in until the button touches, then turn two more turns so the cork rotates in the neck, and pull again. Compare the peak forces. Compare also with a commercial corkscrew.

مواد مورد نیاز این مرحله:

چوب‌پنبه‌هاچوب‌پنبه‌ها6 قطعه
مجموعه چوب‌پنبه‌گذاری بطری شرابمجموعه چوب‌پنبه‌گذاری بطری شراب1 قطعه
چوب‌پنبه‌بازکنچوب‌پنبه‌بازکن1 قطعه

ابزارهای مورد نیاز:

نیروسنج (ترازوی فنری)نیروسنج (ترازوی فنری)
5

A cork that will not come out cleanly

Cork removal problems.

Flow

Loading...
6

History and honest limits

**Samuel Henshall** was granted **British patent No. 2061** on 24 August 1795 — the first patent for a corkscrew. Matthew Boulton made Henshall's corkscrews at Soho, Birmingham, marked "Obstando Promoves". Later designs added threads, levers and wings to take the effort out of the pull. **Honest limits.** The cork pressure and friction in the notebook are illustrative; measure your own pulls. The patent itself is not in the patent databases used for this programme; its details here come from museum and patent-office sources.

مواد

7

ابزارهای لازم

8

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...