همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
The Ferguson Hitch: A Virtual Pivot Ahead of the Axle
Martin

ایجاد شده توسط

Martin

27. سپتامبر 2026NO
۳۳
۰
۰
۰
۰

The Ferguson Hitch: A Virtual Pivot Ahead of the Axle

A plough pinned to a tractor's drawbar behind the rear axle does two bad things: on a hillside it slides downhill with the tractor's tail, and when the driver steers away from a crop row it swings the wrong way first, into the crop. Harry Ferguson of Belfast replaced the pin with two links whose rear ends are wider apart than their front ends. Produced forward, their centre lines meet at a point ahead of the real joints, and the implement swings as if hitched there — so it follows the steering. US 1,916,945, filed 6 June 1929 and granted 4 July 1933, adds a lower link so the implement keeps vertical freedom and an effective line of draft that holds it in the ground, as in his earlier US 1,464,130. This rung finds the virtual centre from the link geometry, shows why it follows the steering, works out how the line of draft loads the rear wheels, and builds a plan-view model to prove it.
متوسط
About 3 hours

دستورالعمل‌ها

1

Virtual centre, steering response and line of draft

در حال بارگذاری دفترچهٔ Jupyter…
2

Build a plan-view hitch model

Cut a tractor outline from plywood about 300 mm long and mark its rear axle line. Screw two pivots behind the axle, 50 mm apart. Cut two balsa links 200 mm long, and a balsa 'implement' bar with two pivots 90 mm apart. Pin the links between them with machine screws so they converge towards the tractor, as in Ferguson's Fig. 2. Lay a steel rule along each link and draw its line forward on the tractor board: the lines cross ahead of the axle. That is the virtual centre. Now pin a second implement to a single screw 100 mm behind the axle. Pull the tractor slowly along a paper strip marked as a crop row and steer it left by turning it about a point on its axle line. Watch each implement's tip: the single-pin one swings right before it follows; the linked one moves left at once. Measure the swing with a protractor at each position.

مواد مورد نیاز این مرحله:

ورق تخته‌سه‌لاورق تخته‌سه‌لا1 قطعه
ورق چوب بالساورق چوب بالسا1 قطعه
پیچ‌های ماشینیپیچ‌های ماشینی8 قطعه

ابزارهای مورد نیاز:

خط‌کشخط‌کش
نقالهنقاله
دریل شارژیدریل شارژی
مجموعه متهمجموعه مته
ماژیک ثابتماژیک ثابت
3

Read the second sheet: the lower link

Sheet 2 shows the modification of Figs. 3 and 4. The two links (4, 5) now run from the tractor to cranks on a cross shaft 8 carried high on a triangular frame on the implement, and a **lower link 6** is universally jointed between the implement frame and the rear of the tractor. The patent: "This form of upper and lower linkage permits the implement to have vertical and lateral freedom while giving a virtual swinging centre forward of the actual connection and an effective line of draft from a point other than the said actual connection." Turning the cross shaft with lever 9 changes the angle of the implement to the tractor, to set the furrow width or keep a cultivator on its rows. Swap the roles — two lower links and one upper — and add a hydraulic ram to lift them, and this becomes the three-point linkage Ferguson later put into production.
مرحله 3 - Image 1
4

The hydraulic lift that came next

Ferguson's production system lifted the links with a hydraulic ram and used the pull of the implement to control it. The embedded blueprint shows how a hand pump and a ram multiply force — the same principle.
5

History and context

**Harry Ferguson** filed **US 1,916,945**, *Tractor Drawn Agricultural Implement*, on 6 June 1929 (British priority 3 July 1928); it was granted 4 July 1933. It builds on his **US 1,464,130** of 7 August 1923. The Ferguson-Brown tractor of 1936 carried a three-point linkage lifted by hydraulics, and from 1939 the Ford 9N tractor was built with the Ferguson system. Three-point linkages are now standardised in sizes, so implements fit tractors of every make. **Honest limits.** The virtual centre helps the implement follow the steering, but a mounted implement also moves the tractor's balance: heavy rear-mounted tools lift weight off the front axle and can make steering light. The simple statics in the notebook ignore wheel slip and soil variation, which real draft control has to cope with.

مواد

3

ابزارهای لازم

5
  • جایگزین
  • جایگزین
  • 1 vendor sell this, none ship to you yet
    جایگزین
  • جایگزین
  • جایگزین

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...