هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
The Finger-Valve Fountain Bath Brush: Press to Run, Let Go to Stop
YourGrandma

ایجاد شده توسط

YourGrandma

6. اکتبر 2026IS
۳۱
۰
۰
۰
۰

The Finger-Valve Fountain Bath Brush: Press to Run, Let Go to Stop

A bath brush fed from a hose runs all the time, or needs a tap out of reach. Daniel S. Koons and William F. Moughler of Chicago received US 634,527, dated 10 October 1899, for "a fountain bath-brush": a false back with a water passage, joined to the brush by a hollow screw whose perforated head lets the water out among the bristles, with a valve that a spring and the water pressure hold shut until a finger presses its stem, and a strap that holds the hand to the brush. This rung works out the finger force, then builds the false back on a scrub brush with a tyre valve as the finger valve, and measures the force and the flow.
متوسط
About 3 hours

دستورالعمل‌ها

1

Force to open the valve

در حال بارگذاری دفترچهٔ Jupyter…
2

A brush that feeds itself before it

The embedded blueprint feeds soap from inside a shaving brush. Koons and Moughler feed water, and give the finger a valve to start and stop it.
3

Read US 634,527

"Said valve is held normally closed by means of a spring 9 and also by the water-pressure, as will be obvious." "A strap k is secured at the sides of said back B' and passes over the latter, so that by inserting the hand between said back B' and said strap k the brush can be firmly held and the fingers at the same time kept in position to operate the valve."
4

Bore the false back

Cut a hardwood block 120 × 50 × 22 mm. Drill a 6 mm passage 90 mm along its centre from one end, and a 6 mm hole down from the top to meet it 30 mm from the far end.

مواد مورد نیاز این مرحله:

قطعهٔ چوب سختقطعهٔ چوب سخت1 قطعه

ابزارهای مورد نیاز:

گیرهٔ رومیزیگیرهٔ رومیزی
دریل شارژیدریل شارژی
مجموعهٔ متهٔ نوک‌مرکزیمجموعهٔ متهٔ نوک‌مرکزی
خط‌کشخط‌کش
عینک ایمنی شفافعینک ایمنی شفاف
5

Fit the finger valve

Drill a hole across the passage 20 mm from the inlet to take a tyre valve, pin upward. Epoxy it in so the water must pass through it.

مواد مورد نیاز این مرحله:

والو لاستیکوالو لاستیک1 قطعه
اپوکسی دوجزئیاپوکسی دوجزئی1 قطعه

ابزارهای مورد نیاز:

دریل شارژیدریل شارژی
مجموعه متهمجموعه مته
6

Join it to the brush

Drill a 6 mm hole through the scrub brush's back to line up with the outlet. Cut a rubber gasket, and screw the block on with four wood screws.

مواد مورد نیاز این مرحله:

برس سایشبرس سایش1 قطعه
ورق لاستیکورق لاستیک1 قطعه
پیچ چوب #8 در ۱ اینچپیچ چوب #8 در ۱ اینچ1 قطعه

ابزارهای مورد نیاز:

دریل شارژیدریل شارژی
مجموعه متهمجموعه مته
چاقوی کاردستیچاقوی کاردستی
مجموعه پیچ‌گوشتیمجموعه پیچ‌گوشتی
7

Strap and hose

Screw a strip of rubber sheet across the block as a hand strap, over the valve's side. Fit a hose connector to the inlet with brass fittings and PTFE tape.

مواد مورد نیاز این مرحله:

ورق لاستیکورق لاستیک1 قطعه
پیچ چوب #8 در ۱ اینچپیچ چوب #8 در ۱ اینچ1 قطعه
اتصالات برنجیاتصالات برنجی1 قطعه
نوار آب‌بندی رزوه از PTFEنوار آب‌بندی رزوه از PTFE1 قطعه

ابزارهای مورد نیاز:

مجموعه پیچ‌گوشتیمجموعه پیچ‌گوشتی
آچار فرانسهآچار فرانسه
8

The patent drawing

US 634,527 drawing sheet, public domain (expired patent).
مرحله 8 - Image 1
9

Measure force and flow

Connect the garden hose and turn on the tap. Press the valve pin with the force meter's hook until water runs; note the force. Hold it open over the jug for 30 s and read the flow.
مرحله 9 - Image 1

مواد مورد نیاز این مرحله:

آبآب1 قطعه

ابزارهای مورد نیاز:

نیروسنج (ترازوی فنری)نیروسنج (ترازوی فنری)
پارچ اندازه‌گیریپارچ اندازه‌گیری
کرونومترکرونومتر
شلنگ باغبانیشلنگ باغبانی
10

A valve that drips, sticks or barely flows

Finger-valve bath brush troubleshooting.

Flow

Loading...
11

History and honest limits

**Daniel S. Koons** and **William F. Moughler** of Chicago filed US 634,527 on 21 September 1898; it is dated 10 October 1899. They called it a self-cleansing brush. Its handle is telescopic, with a stuffing-box between the two members, and the hose can be led through it to the brush; a second form uses a nozzle as the screw joining the backs. They did not limit it to the bath. **Honest limits.** A tyre valve stands in for their seated valve and stem, and wood screws for their hollow screw. Your forces and flows are the result.

مواد

9

ابزارهای لازم

13

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...