همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
The Rotary Tiller: Blades That Cut the Soil in Slices
Martin

ایجاد شده توسط

Martin

27. سپتامبر 2026NO
۴۷
۰
۰
۰
۰

The Rotary Tiller: Blades That Cut the Soil in Slices

A plough and harrow need several passes and a heavy tractor to pull them, and the wheels pack the soil they have just loosened. A rotary tiller drives its blades round from the engine: they chop down into the soil in slices, throw it back against a hood and leave it loose in one pass — and because the blades push backwards, they help drive the machine forwards instead of dragging on it. Arthur Clifford Howard began experimenting with rotary tillage on his father's farm at Gilgandra, New South Wales, in 1912, found that the ground could be tilled without packing it, and settled on L-shaped blades on widely spaced flanges on a small rotor. He patented a design with an internal combustion engine in 1920, and in 1922 formed Austral Auto Cultivators, later Howard Auto Cultivators. This rung plots the blade paths, works out the bite length that sets the tilth, and builds a drill-driven rotor to check it in sand.
متوسط
About 4 hours

دستورالعمل‌ها

1

Blade paths and bite length

در حال بارگذاری دفترچهٔ Jupyter…
2

Build a bench rotor

Cut six blades 120 mm long from 20 mm spring steel strip and bend each 40 mm from one end to a right angle — Howard's L-shape. Drill the long leg twice. Bolt three blades to each of two plywood flanges 100 mm across, at 120 degrees apart, their bent tips all pointing the same way round. Fix the flanges 80 mm apart on a 10 mm threaded rod, the second flange turned 60 degrees from the first so the blades enter the soil alternately. Chuck the rod in a cordless drill. Wear eye protection: blades spinning in sand throw it hard.

مواد مورد نیاز این مرحله:

نوار فولاد فنرنوار فولاد فنر1 قطعه
ورق تخته‌سه‌لاورق تخته‌سه‌لا1 قطعه
میلهٔ رزوه‌شدهمیلهٔ رزوه‌شده1 قطعه
پیچ‌های ماشینیپیچ‌های ماشینی12 قطعه
ماسهٔ ریزماسهٔ ریز20 kilogram

ابزارهای مورد نیاز:

دریل شارژیدریل شارژی
مجموعه متهمجموعه مته
گیرهٔ رومیزیگیرهٔ رومیزی
آچار فرانسهآچار فرانسه
خط‌کشخط‌کش
عینک ایمنیعینک ایمنی
دستکش کار چرمیدستکش کار چرمی
3

Measure the bite

Level damp sand in a long tray and mark a 500 mm run with pins. Measure the drill's speed under load with the tachometer. Lower the spinning rotor into the sand at the start mark and walk it to the end mark at a steady pace, timing it. Each blade leaves a curved cut in the sand. Count the cuts over the 500 mm and divide: that is your bite length. Compare it with $60v/(nz)$ using your measured speed $v$, rotor speed $n$ and $z = 3$ blades per flange. Repeat at half the walking speed: the bites halve and the sand is left finer.

ابزارهای مورد نیاز:

دورسنج دیجیتالدورسنج دیجیتال
کرونومترکرونومتر
کیت پرچم و میخ نقشه‌برداریکیت پرچم و میخ نقشه‌برداری
خط‌کشخط‌کش
4

A tiller leaving poor tilth

Common rotary tiller problems.

Flow

Loading...
5

History and honest limits

**Arthur Clifford Howard** of Gilgandra, New South Wales, began rotary tillage experiments in 1912, powered at first by his father's steam tractor; his earliest designs threw the soil sideways until he developed the L-shaped blade. He patented an engine-driven rotary hoe in 1920 and founded Austral Auto Cultivators in 1922; the Howard Rotavator became a byword for the machine. **Honest limits.** Rotary tilling takes more energy per hectare than ploughing, pulverises soil structure if overused, and can leave a smeared pan at its working depth in wet soil. It is best for seedbeds, gardens and working residue in, not for every field every year.

مواد

5

ابزارهای لازم

10

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...